The NIC dump component didn't support forwarding of link states and link-state
signals until now. Furthermore, it now prints MAC address and link state
on session creation and on every link state change.
Ref #2490
Previously, the uplink session was created on component startup while the
creation of the downlink session is timed by the client component. This
created a time span in which packets from the uplink were dropped at the
nic_dump. Now the uplink session-request is done by the session component
of the downlink.
Ref #2490
Add a "writeable" policy option to the ahci_drv and part_blk Block
servers and default from writeable to ready-only. Should a policy
permit write acesss the session request argument "writeable" may still
downgrade a session to ready-only.
Fix#2469
This should actually never happen. However if it happens, be a bit robuster
and don't provide the memory for re-use (which causes tons of other trouble
afterwards).
Issue #2505
Some x86 machines do have a LAPIC speed < 1000 ticks per millisecond
when configured to use the maximum divider (as it was always the case).
But we need microseconds precision for the timeout framework. Thus,
reduce the divider dynamically until the frequency fullfills our
requirements.
Ref #2400
There are hardware timers whose frequency can't be expressed as
ticks-per-microsecond integer-value because only a ticks-per-millisecond
integer-value is precise enough. We don't want to use expensive
floating-point values here but nonetheless want to translate from ticks
to time with microseconds precision. Thus, we split the input in two and
translate both parts separately. This way, we can raise precision by
shifting the values to their optimal bit position. Afterwards, the results
are shifted back and merged together again.
As this algorithm is not so trivial anymore and used by at least three
timer drivers (base-hw/x86_64, base-hw/cortex_a9, timer/pit), move it to a
generic header to avoid redundancy.
Ref #2400
Due to the simplicity of the algorithm that translated from timer ticks
to time, we lost microseconds precision although the timer allows for it.
Ref #2400
Due to the simplicity of the algorithm that translated from timer ticks
to time, we lost microseconds precision although the timer allows for it.
Ref #2400
When synchronizing with the remote time source, we have to take care that the
measured time difference cannot become null because its real value is smaller
than the measurement granularity. Since the granularity is one microsecond, we
simply go on polling timestamp and time until the microsecond has passed.
This busy waiting should be no problem for the system for two reasons. First,
it is limited to a relatively small amount of time and second, a busy lock
does not happen because the time source that is responsible for the limiting
factor is explicitely called on each poll.
Ref #2400
When building Genode on a Linux system running in a Xen Dom0, the 'xen'
run target can run a Genode scenario in a Xen DomU.
Usage: in build/x86_*/etc/build.conf, define:
RUN_OPT = --include boot_dir/$(KERNEL) --include image/iso --include power_on/xen --include log/xen --include power_off/xen
The Xen DomU runs in HVM mode and loads Genode from an ISO image. Serial
log output is printed to the console and graphical output is shown in an
SDL window.
The Xen DomU ist managed using the 'xl' command line tool and it is
possible to add configuration options in the 'xen_args' variable in a run
script. Common options are:
- disabling the graphical output:
append xen_args { sdl="0" }
- configuring a network device:
append xen_args { vif=\["model=e1000,mac=02:00:00:00:01:01,bridge=xenbr0"\] }
- configuring USB input devices:
append xen_args { usbdevice=\["mouse","keyboard"\] }
Note: the 'xl' tool requires super-user permissions and interactive
password input can be troublesome in combination with 'expect' and is not
practical for automatic tests. For this reason, the current implementation
assumes that no password input is needed when running 'sudo xl', which can
be achieved by creating a file '/etc/sudoers.d/xl' with the content
'user ALL=(root) NOPASSWD: /usr/sbin/xl'
(where 'user' is the Linux user name).
Fixes#2504
When running core as the kernel inside every component, a separate
stack area for core is needed that is different from the user-land
component's one.
Ref #2091
Acquire Signal_context objects locks via Object_pool::apply() in the
context of the entrpyoint thread, instead in the context of the calling
thread.
Fixes#2485
The files are generated via flex and bison. Until now, this step was
performed when preparing the libc port. Unfortunately, the generated
files have subtle differences depending on the flex/bison versions
installed in the host. For example, the bison version number appears in
the generated code. This, in turn, breaks the hash mechanism of the
depot where a src/libc archive ends up being slightly different when
created on different hosts.
By moving the code generation to the build stage, the src/libc archive
merely contains the nslexer.l and nsparser.y source files but not the
generated files.
- Fix fatal exception handling so that stack traces are dumped
- Add 'include/nim' directories to Nim module search path
- Enable release optimizations for release builds
Fix#2493
This patch removes the assertion about the unexpected call of
'block_for_signal' within core. On Linux, this call is actually
expected because of the handling of SIGCHLD signals by core.
When idle, menu_view de-schedules timer events to save processing time.
Once reactivated by a dialog update, it computes the passed time and
applies the result to the animator. However, the animation was most likely
started by the update not during the sleep. So the passed time must not
be applied to the animation in this case. Otherwise, many animation steps
are computed at once within a single visible frame.
Furthermore, the patch adjusts the REDRAW_PERIOD to 2, which is a better
value for geometric movements as opposed to mere color-blending effects
where the frame rate does not matter so much.
It also refines the nitpicker-buffer relocation in a way that extends
the buffer but does not shrink it. This lowers the interaction with
nitpicker in situations where the dialog size changes a lot.
By applying the text output to the alpha buffer in addition to the pixel
buffer, labels can now appear without the need for an underlying frame
or button.
The new widget allows one to align a child widget within a larger parent
widget by specifying the boolean attributes 'north', 'south', 'east',
and 'west'. If none is specified, the child is centered. If opposite
attributes are specified, the child is stretched.
This improves the output quality of antialiased lines onto a transparent
nitpicker buffer. For antialiased graphics operations, the initial color
leaks through. Leaking 50% gray is better than leaking black, in
particular when drawing white lines.
This patch makes the use of 'List' invisible at the 'Animator'
interface. This allows users of the utility to keep 'Animator::Items' in
a custom 'List' with no aliasing problems.
The VFS library can be used in single-threaded or multi-threaded
environments and depending on that, signals are handled by the same thread
which uses the VFS library or possibly by a different thread. If a VFS
plugin needs to block to wait for a signal, there is currently no way
which works reliably in both environments.
For this reason, this commit makes the interface of the VFS library
nonblocking, similar to the File_system session interface.
The most important changes are:
- Directories are created and opened with the 'opendir()' function and the
directory entries are read with the recently introduced 'queue_read()'
and 'complete_read()' functions.
- Symbolic links are created and opened with the 'openlink()' function and
the link target is read with the 'queue_read()' and 'complete_read()'
functions and written with the 'write()' function.
- The 'write()' function does not wait for signals anymore. This can have
the effect that data written by a VFS library user has not been
processed by a file system server yet when the library user asks for the
size of the file or closes it (both done with RPC functions at the file
system server). For this reason, a user of the VFS library should
request synchronization before calling 'stat()' or 'close()'. To make
sure that a file system server has processed all write request packets
which a client submitted before the synchronization request,
synchronization is now requested at the file system server with a
synchronization packet instead of an RPC function. Because of this
change, the synchronization interface of the VFS library is now split
into 'queue_sync()' and 'complete_sync()' functions.
Fixes#2399
This patch enables one to supply a list of arguments to
'install_config'. The arguments appear concatenated in the resulting
config file. This is useful for embedding dynamically generated content
into an otherwise static configuration. For example, in the following
config, the 'pkg' attribute of the '<query>' config node is defined by
the return value of the 'query_pkg' function:
install_config {
<config>
...
<start name="depot_query">
...
<config>
<query pkg="genodelabs/pkg/} [query_pkg] {"/>
</config>
</start>
</config>}
This patch changes init's service forwarding such that pending requests
are kept unanswered as long as the requested service is not present
(yet). In dynamic-init scenarios, this is needed in situtions where the
dynamic init is known to eventually provide the service but the internal
subsystem is not ready yet. Previously, a client that attempted to
request a session in this early phase would get a 'Service_denied'
exception. By deferring the forwarding in this situation, the behaviour
becomes deterministic.
If a matching '<service>' exists but there is no matching policy sub
node, the request is answered with 'Service_denied' - as expected.
A boot module with size 0 previously made Core crash with a page fault in
Region_map_component::attach. This patch prevents the creation of ROM-FS
entries for such modules.
Ref #2490
For most base platforms (except linux and sel4), the initialization of
boot modules is the same. Thus, merge this default implementation in the
new unit base/src/core/platform_rom_modules.cc.
Ref #2490
In Region_map_component::attach, storing the metadata for a region may
throw an exception. Catch it and throw an Invalid_dataspace exception.
Ref #2490
Currently, init does not test wether a service is abandoned on a new
configuration if the service was routed via an any-child route. Trigger
this behaviour in the init test.
Ref #2483
We used a hardware timer locally in the RPI USB driver because a timer
connection was not precise enough to fullfill the host controllers
requirements.
With the modern timer connection interface, however, reading out time at
a connection is microseconds precise and we can remove the local timer.
But we cannot use the same timer connection for doing legacy-interface
stuff like usleep (currently used in LX kit) and modern-interface stuff
like curr_time. Thus, we open two connections for now.
Ref #2400
The calibration of the interpolation parameters was previously only done
periodically every 500 ms. Together with the fact that the parameters
had to be stable for at least 3 calibration steps to enable
interpolation, it took at least 1.5 seconds after establishing a
connection to get microseconds-precise time values.
This is a problem for some drivers that directly start to poll time.
Thus, the timer connection now does a calibration burst as soon as it
switches to the modern mode (the mode with microseconds precision).
During this phase it does several (currently 9) calibration steps
without a delay inbetween. It is assumed that this is fast enough to not
get interrupted by scheduling. Thus, despite being small, the measured
values should be very stable which is why the burst should in most cases
be sufficient to get the interpolation initialized.
Ref #2400
When in modern mode (with local time interpolation), the timer
connection used to maximize the left shifting of its
timestamp-to-microseconds factor. The higher the shift the more precise
is the translation from timestamps to microseconds. If the timestamp
values used for determining the best shift were small - i.e. the delay
between the calibration steps were small - we may got a pretty big
shift. If we then used the shift with bigger timestamp values - i.e.
called curr_time seldom or raised calibration delays - the big shift
value became a problem. The framework had to scale down all measured
timestamps and time values temporarily to stay operative until the next
calibration step.
Thus, we now raise the shift only that much that the resulting factor
fullfills a given minimum. This keeps it as low as possible according
to the precision requirement. Currently, this requirement is set to 8
meaning that the shifted factor shall be at least 2^8 = 256.
Ref #2400
The kernel timer on RPI is able to measure time microseconds-precise.
Howeer, due to a bug, we dropped precision during the ticks-to-time
translation and return only milliseconds-precise time.
Ref #2400
As the timer session now provides a method 'elapsed_us', there is no more need
for doing any internal calculations with values of milliseconds.
Ref #2400
As timer sessions are not expected to be microseconds precise (because
of RPC latency and scheduling), the session interface provided only a
method 'elapsed_ms' although the back end of this method in the timer
driver works with microseconds.
However, in some cases it makes sense to have a method 'elapsed_us'. The
values it returns might be milliseconds away from the "real" time but it
allows you to work with delays smaller than a millisecond without
getting a zero delta value.
This commit is motivated by the need for fast bursts of calibration
steps for the time interpolation in the new timer connection.
Ref #2400
The filename buffer of a dataspace in base-linux is limited to
40 bytes. When using file names longer than this, the remainder
gets dropped silently. Add an error message to aid debugging this
case.
This is helpful for disabling messages in etc/tools.conf by
setting it to e.g.
MSG_LINK = @true ""
This results in much shorter and less cluttered logs in automatic
builds.
- factor out Rm_client::pager lambda code into utility
Region_map_component::create_map_item
- use utility to find/lookup physical addresses to be mapped eagerly
Issue #2209
The launcher.run scenario was last updated mid-may of the recently
developed cap-quota accounting (before all cap types were covered).
Hence, the quotas used in the scenario are too low. This patch adjusts
the values such that the scenario can be started on NOVA on Qemu. It
also fixes a warning about a deprecated way of configuring the
report_rom component.
Thanks to Jörg-Christian Böhme for reporting!
- Update FatFS port from 0.07e to 0.13
- Multi-device support
- Basic test at run/fatfs
- Adaption of existing components
Note, ffat is now consistently renamed to fatfs.
Ref #2410
rm_fault.run triggers write on read-only ROM provided by core, which
fails without this patch:
arm - "raised unhandled data abort"
x86 - (silent/invisible) busy loop because write fault gets never resolved
The run script did not consider the routing for the environment ROM
sessions for the test-iso component. It routed all ROM sessions -
including the ones for the executable and the dynamic linker - to
fs_rom. The patch also adds the cap quota definitions required since
version 17.05 and fixes a whitespace inconsistency between the test
program and the run script.
Thanks to Steven Harp for reporting!
This is expected by hardware terminals, ie., terminal programs connected
to null-modem serial connections. Otherwise, the next line starts at the
column right after the last line.
Platform_pd "_pd" uses a allocator for, which relies on the mapped RAM
dataspace within core. Unfortunately the RAM dataspaces are already freed up
during _ram_ds_factory destruction, which may lead to trouble if accessed
afterwards.
Issue #2451
relocation is required, to avoid overlapping phdr in the elf binaries, but
sel4 will fail to boot if bender relocates the images at the end of physical
memory. Limit the physical relocation address to a fixed 256M value, so that
sel4 will work.
Issue #2451
The new version of the test exercises the combination of fs_report with
ram_fs and fs_rom as a more flexible alternative to report_rom.
It covers two corner cases that remained unaddressed by fs_rom and
ram_fs so far: First, the late installation of a ROM-update signal
handler at fs_rom right before the content of the file is modified.
Second, the case where the requested file is not present on the file
system at the creation time of the ROM session. Here, the ram_fs missed
to inform listeners for the compound directory about the later created
file.
This patch ensures that fs_rom delivers a ROM-update notification in the
case where the underlying file was changed in-between requesting the
initial ROM content and registering the signal handler.
With the introduction of the CONTENT_CHANGED notifications delivered via
the packet stream, the assumption that no more than one READ packet is
in flight at all times does no longer hold. If the fs server responds
to a CONTENT_CHANGED packet while the fs_rom expects the completion of a
read request, the '_update_dataspace' method would prematurely return,
leaving the dataspace unpopulated. This patch solves the problem by
specifically waiting for the completion of the read request.
Session_requester inherits from Dynamic_rom_session::Content_producer
which specifies the Buffer_capacity_exceeded exception which is thrown
on insufficient buffer space.
The former use of 'arm_v7' as architecture was too unspecific. Depot
binary archives for Cortex-A8/A9 platforms should be generated for
the 'arm_v7a' architecture to define the required compile flags
(i.e., -march).
This patch sets the -march complile flag in spec/arm_v7a.mk, which
enables us to build depot archives for the 'arm_v7a' architecture.
It also removes copy-pasted comments that offer no valuable insights but
contain grammar errors.
On platforms that use the PIT timer driver, 'elapsed_ms' is pretty
inprecise/unsteady (up to 3 ms deviation) for a reason that is not
clearly determined yet. On Fiasco and Fiasco.OC, that use kernel timing,
it is the same. So, on these platforms, our locally interpolated time
seems to be fine but the reference time is bad. Until this is fixed, we
raise the error tolerance for these platforms in the run script.
Ref #2400
Appending a suffix to report filenames was behavior inherited from
fs_log, it prevents creating files where directories need to be created
later. But unlike logs, only a subset of the hierarchy will report and
those that do append a component-local label, so the risk of collision
is low.
By removing the suffix fs_rom can serve reports back as ROM just as
report_rom does.
Ref #2422
When building with multiple jobs, the 'Makefile' rule may be executed
before any of its sibling rules, which implicitly create the target
directory. In this case, the attempt to create the symlink for
'Makefile' fails and the 'build_bin_archive' aborts. Analogously to the
sibling rules, this fix creates the target directory as a side effect of
the 'Makefile' rule.
This patch makes the build step of the create tool conditional. If
merely creating api, src, pkg, or raw archives, the invocation of the
'build' tool can be skipped. Otherwise, the heap message for the 'build'
tool is displayed (because it is called w/o any arguments), which is
misleading to the user.
A bug in the timer-ticks-to-microseconds translation of the kernel timer
caused the user time to periodically get stuck for about 32 milliseconds
and then jump forward to the normal level again.
Ref #2400
In the timeout framework, we maintain a translation factor value to
translate between time and timestamps. To raise precision we scale-up
the factor when we calculate it and scale-down the result of its
appliance later again. This up and down scaling is achieved through
left and right shifting. Until now, the shift width was statically
choosen. However, some platforms need a big shift width and others a
smaller one. The one static shift width couldn't cover all platforms
which caused overflows or precision problems.
Now, the shift width is choosen optimally for the actual translation
factor each time it gets re-calculated. This way, we can take care that
the shift always renders the best precision level without the risk for
overflows.
Ref #2400
The result-buffer related members of the fast polling test are
the same for each buffered result type. Thus, we can make the
code easier by providing them through a struct.
Ref #2400
This patch increases init's preserved RAM and capability quota to
account for a current limitation of init with respect to the creation of
sessions to parent services:
In contrast to regular routed services, sessions to parent services are
created via 'Env::session'. The implementation of 'Env::session'
automatically upgrades session quotas on demand, which is the desired
behavior for regular 'Connection' objects. However, for sessions
established on the behalf of init's children, we would need to reflect
the error condition to the child instead of resolving it locally within
init (by subsidizing the session with init's quota). This patch leaves
this issue unresolved but fixes the symptom for the bomb test. It is
meant as an interim solution until the handling of parent sessions is
revised.
This patch decouples the error handling of the quota transfers
and the actual session creation. In the previous version, an error in
the 'initiate_request' phase would leave the local scope via an
exception without disarming the transfer guard objects. This way,
the guard destructors would attempt the returning of session quota in
addition to the explicit call of '_revert_quota_and_destroy' as done in
the error handling of the 'initiate_request' operation.
In the presence of a session-creation error in the 'initiate_request'
phase, session quota would eventually be returned twice. This patch
removes the intertwined error handling of both phases in a way that the
guards of the first phase (quota transfer) are no longer present in the
second phase (initiate_request).
This patch makes sure that the initial PD session limit (as defined by
the client-provided session quota) is preserved over the entire lifetime
of the PD session. That means, it cannot be transferred to other PD
sessions. Otherwise, it may be impossive to hand back all the static
session quota to the PD-session client at session-destruction time
because parts of the initial quota would no longer belong to the
session.
Note that the initial limit can still be used for allocations within the
PD session as those allocations are automatically reverted at
session-destruction time.
The implementations of the lock and C++ guards tests depend on
thread-execution priorities, which produces false negatives of the whole
thread test on platforms without priority support.
On QEMU, NOVA uses the pretty unstable TSC emulation as primary time
source. Thus, timeouts do not trigger with the common precision (< 50
ms). Use an error tolerance of 200 ms for this platform constellation.
Ref #2400
Apparently this construct leads to a compiler errors like
error: second operand to the conditional operator is of type ‘void’, but
the third operand is neither a throw-expression nor of type ‘void’
The fast polling test uses one timer session for raw 'elapsed_ms' calls
and another one for potentially interpolated 'curr_time' calls. It then
compares the two results against each other. However, until now, the
test did not consider that the duration of the session construction may
create a remarkable shift between the local times of the two sessions.
This shift is now determined and compensated before doing any
comparison.
Ref #2400
The multiple-handlers test was checking if handlers at one signal were
activated in a fair manner. But on Qemu, the error tolerance of one was
too small in rare cases (2 of 100 runs). However, having multiple
handlers for the same signal context can be considered deprecated
anyway. With the recommended Signal_handler wrapper for signal sessions,
you can't use this feature. Thus, we removed the multiple-handlers test.
Fixes#2450
The recently implemented capability resource trading scheme unfortunately
broke the automated capability memory upgrade mechanism needed by base-hw
kernel/core. This commit splits the capability memory upgrade mechanism
from the PD session ram_quota upgrade, and moves that functionality
into a separate Pd_session::Native_pd interface.
Ref #2398
The depot tool did not consistently distinct libraries from regular
targets when handling binary archives. The binary archive of a regular
target is located at <user>/<bin>/<arch>/<name> whereas a library is
located at <user>/<bin>/<arch>/<api>/<name>.
Fixes#2438
We incorrectly used 'unsigned long' (which is 32 or 64 bit depending on
the CPU architecture) for a timestamp (which is always 64 bit) in the
timer-connection implementation.
Ref #2435
On platforms were we do not have local time interpolation we can simply
skip the first test stage in the timeout test. This way, we can at least
test the rest.
Fixes#2435
On ARM, we do not have a component-local hardware time-source. The ARM
performance counter has no reliable frequency as the ARM idle command
halts the counter. Thus, we do not do local time interpolation on ARM.
Except we're on the HW kernel. In this case we can read out the kernel
time instead.
Ref #2435
This patch replaces the toy downloader (that merely copied files
locally, for testing) with the mechanics needed to download files from a
www server.
It also changes the use of GPG to use detached signatures.
Issue #2339
VM-exit interruption info was dropped and Vbox only needs guest CR3
value for guest-physical memory translation but does not actually change
it since the VM is running in unrestricted guest mode.
The explicit relative location of the file instructed both target builds
to generate ../main.o which gloriously fails with parallel builds. The
produced range of error messages was astonishing ranging from "file
truncated" to "TLS reference in ../main.o mismatches non-TLS reference
in ../main.o".
E.g., the script manually tried to configure lighttpd and used the old
porting directory structure that was integrated in the repos. For the
same reason it produced compile errors with noux packages.
Ref #2398
We do not have debug symbols in the bin/ binaries anymore. Thus, use the
debug/ binaries instead. We now have kernel specific binary names for
ld.lib.so and some others. Adapt, to this fact as well. For doing so
without unnecessary output, provide a new parameter "silent" at the
"kernel_specific_binary" procedure.
Ref #2398
A dataspace capability request to a ROM service may invalidate any
previously issued dataspace. Therefor no requests should be made while a
session dataspace is mapped. Reducing calls to the session also improves
performance where servicing a ROM request has a significant cost.
Fix#2418
There are programs, e.g. curl, that check if a connection was
established successfully by looking at SO_ERROR. Pretend that
the getsockopt() call was executed to keep them happy. If they
try to use a broken connection, the other socket functions will
bail.
This patch changes the noux build rules to produce a tar archive in
'bin/', alleviating the need for this step from the run scripts.
This way, the visible result of a built noux package is a single (tar)
file in '<build-dir>bin/', which is suited for the use as a ROM module.
The 'Stack_area_ram_session' is now a 'Stack_area_ram_allocator', which
simplifies the code and remove a dependency from the 'Ram_session'
interface, which we want to remove after all.
Issue #2407
By supplying a statically allocated initial block to the slab allocator
for signal contexts, we become able to construct a 'Signal_broker' (the
back end for the PD's signalling API) without any dynamic memory
allocation. This is a precondition for using the PD as meta-data
allocator for its contained signal broker (meta data allocations must
not happen before the PD construction is complete).
Issue #2407
If a child is allowed to constrain physical memory allocations but left
the 'phys_start' and 'phys_size' session arguments blank, init applies
builtin constraints for allocating DMA buffers.
The only component that makes use of the physical-memory constraint
feature is the platform driver. Since the built-in heuristics are
applied to the platform driver's environment RAM session, all
allocations performed by the platform driver satisfy the DMA
constraints.
To justify building-in these heuristics into init as opposed to
supplying the values as configuration arguments, the values differ
between 32 and 64 bit. The configuration approach would raise the need
to differentiate init configurations for both cases, which are
completely identical otherwise.
Issue #2407
This commit removes support for limitation of RAM allocations from the
platform_drv. A subsequent commit adds this feature to init.
Issue #2398
Issue #2407
By separating the session-interface concerns from the mechanics of the
dataspace creation, the code becomes simpler to follow, and the RAM
session can be more easily merged with the PD session in a subsequent
step.
Issue #2407
This patch allows core's 'Signal_transmitter' implementation to sidestep
the 'Env::Pd' interface and thereby adhere to a stricter layering within
core. The 'Signal_transmitter' now uses - on kernels that depend on it -
a dedicated (and fairly freestanding) RPC proxy mechanism for signal
deliver, instead of channeling signals through the 'Pd_session::submit'
RPC function.
With the capability-quota mechanism, the terminal-session won't always
be constructed completely on the first try (we may run out of caps in
the middle of the construction). Therefore, all members of the object
must be properly destructable. Furthermore, the patch replaces the
sliced heap by a heap to avoid allocating a new dataspace for each line
of the cell array.
Previously, the Genode::Timer::curr_time always used the
Timer_session::elapsed_ms RPC as back end. Now, Genode::Timer reads
this remote time only in a periodic fashion independently from the calls
to Genode::Timer::curr_time. If now one calls Genode::Timer::curr_time,
the function takes the last read remote time value and adapts it using
the timestamp difference since the remote-time read. The conversion
factor from timestamps to time is estimated on every remote-time read
using the last read remote-time value and the timestamp difference since
the last remote time read.
This commit also re-works the timeout test. The test now has two stages.
In the first stage, it tests fast polling of the
Genode::Timer::curr_time. This stage checks the error between locally
interpolated and timer-driver time as well as wether the locally
interpolated time is monotone and sufficiently homogeneous. In the
second stage several periodic and one-shot timeouts are scheduled at
once. This stage checks if the timeouts trigger sufficiently precise.
This commit adds the new Kernel::time syscall to base-hw. The syscall is
solely used by the Genode::Timer on base-hw as substitute for the
timestamp. This is because on ARM, the timestamp function uses the ARM
performance counter that stops counting when the WFI (wait for
interrupt) instruction is active. This instruction, however is used by
the base-hw idle contexts that get active when no user thread needs to
be scheduled. Thus, the ARM performance counter is not a good choice for
time interpolation and we use the kernel internal time instead.
With this commit, the timeout library becomes a basic library. That means
that it is linked against the LDSO which then provides it to the program it
serves. Furthermore, you can't use the timeout library anymore without the
LDSO because through the kernel-dependent LDSO make-files we can achieve a
kernel-dependent timeout implementation.
This commit introduces a structured Duration type that shall successively
replace the use of Microseconds, Milliseconds, and integer types for duration
values.
Open issues:
* The timeout test fails on Raspberry PI because of precision errors in the
first stage. However, this does not render the framework unusable in general
on the RPI but merely is an issue when speaking of microseconds precision.
* If we run on ARM with another Kernel than HW the timestamp speed may
continuously vary from almost 0 up to CPU speed. The Timer, however,
only uses interpolation if the timestamp speed remained stable (12.5%
tolerance) for at least 3 observation periods. Currently, one period is
100ms, so its 300ms. As long as this is not the case,
Timer_session::elapsed_ms is called instead.
Anyway, it might happen that the CPU load was stable for some time so
interpolation becomes active and now the timestamp speed drops. In the
worst case, we would now have 100ms of slowed down time. The bad thing
about it would be, that this also affects the timeout of the period.
Thus, it might "freeze" the local time for more than 100ms.
On the other hand, if the timestamp speed suddenly raises after some
stable time, interpolated time can get too fast. This would shorten the
period but nonetheless may result in drifting away into the far future.
Now we would have the problem that we can't deliver the real time
anymore until it has caught up because the output of Timer::curr_time
shall be monotone. So, effectively local time might "freeze" again for
more than 100ms.
It would be a solution to not use the Trace::timestamp on ARM w/o HW but
a function whose return value causes the Timer to never use
interpolation because of its stability policy.
Fixes#2400
This patch make sure that a once managed parent RPC object will always be
dissolved if an exception during the remaining child construction
occurs. The original version would miss the dissolve call if one of the
subsequent members throws an exception at construction time.
With this, we get rid of platform specific timer interfaces. The new
Timer class does the same as the old Clock class and has a generic
interface. The old Timer class was merely used by the old Clock class.
Also, we get rid of having only one timer instance which we tell with
each method call for which CPU it shall be done. Instead now each Cpu
object has its own Timer member that knows the CPU it works for.
Also, rename all "tics" to "ticks".
Fixes#2347
Removes the following Fiasco.OC specific features:
* GDB extensions for Fiasco.OC
* i.MX53 support for Fiasco.OC
* Kernel debugger terminal driver
* Obsolete interface Native_pd
* Obsolete function of interface Native_cpu
Previously we did write the SPSR via an MSR instruction without
additional flags. Unfortunately, this tells the CPU to write the
register only partially. This often isn't a problem as the users PSR
reset value normally is conform to our expectations but in some cases
(e.g. PSR endianess bit on WandBoard core #4) the reset value is bad.
Thus, we have to add the CXSF flags (access Control + eXtension + Status
+ Flags) so the CPU overwrites the entire register.
Fixes#2254
Previously, the debugging version of the core image
(<build_dir>/var/run/<run_name>.core) was created by the run tool from
the common core object file
(<build_dir>/var/run/<run_name>/core-<kernel>.o). This object file,
however, was already stripped by the build system and thus didn't
contain debug info anymore. The build system also creates an unstripped
version in <build_dir>/debug/core-<kernel>.o, so we now use this one
for <build_dir>/var/run/<run_name>.core.
Ref #2254
This patch eases the debugging of situations where a session-object
constructor wrongly throws an exception type not specified in the
'Local_service::Factory' interface.
This patch reduces the number of exception types by facilitating
globally defined exceptions for common usage patterns shared by most
services. In particular, RPC functions that demand a session-resource
upgrade not longer reflect this condition via a session-specific
exception but via the 'Out_of_ram' or 'Out_of_caps' types.
Furthermore, the 'Parent::Service_denied', 'Parent::Unavailable',
'Root::Invalid_args', 'Root::Unavailable', 'Service::Invalid_args',
'Service::Unavailable', and 'Local_service::Factory::Denied' types have
been replaced by the single 'Service_denied' exception type defined in
'session/session.h'.
This consolidation eases the error handling (there are fewer exceptions
to handle), alleviates the need to convert exceptions along the
session-creation call chain, and avoids possible aliasing problems
(catching the wrong type with the same name but living in a different
scope).
This patch mirrors the accounting and trading scheme that Genode employs
for physical memory to the accounting of capability allocations.
Capability quotas must now be explicitly assigned to subsystems by
specifying a 'caps=<amount>' attribute to init's start nodes.
Analogously to RAM quotas, cap quotas can be traded between clients and
servers as part of the session protocol. The capability budget of each
component is maintained by the component's corresponding PD session at
core.
At the current stage, the accounting is applied to RPC capabilities,
signal-context capabilities, and dataspace capabilities. Capabilities
that are dynamically allocated via core's CPU and TRACE service are not
yet covered. Also, the capabilities allocated by resource multiplexers
outside of core (like nitpicker) must be accounted by the respective
servers, which is not covered yet.
If a component runs out of capabilities, core's PD service prints a
warning to the log. To observe the consumption of capabilities per
component in detail, the PD service is equipped with a diagnostic
mode, which can be enabled via the 'diag' attribute in the target
node of init's routing rules. E.g., the following route enables the
diagnostic mode for the PD session of the "timer" component:
<default-route>
<service name="PD" unscoped_label="timer">
<parent diag="yes"/>
</service>
...
</default-route>
For subsystems based on a sub-init instance, init can be configured
to report the capability-quota information of its subsystems by
adding the attribute 'child_caps="yes"' to init's '<report>'
config node. Init's own capability quota can be reported by adding
the attribute 'init_caps="yes"'.
Fixes#2398
This patch reworks the implementation of core's RAM service to make use
of the 'Session_object' and to remove the distinction between the
"metadata" quota and the managed RAM quota. With the new implementation,
the session implicitly allocates its metadata from its own account. So
there is not need to handle 'Out_of_metadata' and 'Quota_exceeded' via
different exceptions. Instead, the new version solely uses the
'Out_of_ram' exception.
Furthermore, the 'Allocator::Out_of_memory' exception has become an alias
for 'Out_of_ram', which simplifies the error handling.
Issue #2398
The 'Session_object' unifies several aspects of server-component
implementations:
* It keeps track of session quotas and is equipped with standardized
interfaces (Quota_guard) to upgrade (and in the future potentially
downgrade) session quotas in a uniform way.
* It follows the pattern of modern RPC objects / signal handlers that
manage/dissolve themselves at the entrypoint given as constructor
argument. Thereby, the relationship with its entrypoint is always
coupled with the lifetime of the session-component object.
* It stores the session label, which was previously done manually by
most but not all server-component implementations.
* It stores the session 'diag' flag.
* It is equipped with output methods 'diag', 'error', and 'warning'.
All messages printed from the context of a session component is
automatically prefixed with the session type and client label.
Messages passed via 'diag' are only printed if the 'diag' flag of
the session is set.
Issue #2398
The 'diag' flag can be defined by a target node of a route in init's
configuration. It is propagated as session argument to the server, which
may evaluate the flag to enable diagnostic output for the corresponding
session.
Issue #2398
This patch makes use of the new 'Quota_transfer::Account' by the service
types in base/service.h and uses 'Quota_transfer' objects in
base/child.cc and init/server.cc.
Furthermore, it decouples the notion of an 'Async_service' from
'Child_service'. Init's 'Routed_service' is no longer a 'Child_service'
but is based on the new 'Async_service' instead.
With this patch in place, quota transfers do no longer implicitly use
'Ram_session_client' objects. So transfers can in principle originate
from component-local 'Ram_session_component' objects, e.g., as used by
noux. Therefore, this patch removes a strumbling block for turning noux
into a single threaded component in the future.
Issue #2398
The 'Quota_transfer' helper facilitated the implementation of quota
transfers between components in a transactional manner. It is designated
for framework-internal use (replacing the 'Transfer' class in child.h).
However, since it is also useful for init, we make it publicly
available.
The 'Quota_transfer::Account' class serves as an interface representing
the donor or receiver of quotas (parent, service, client).
Issue #2398
This patch replaces the 'Parent::Quota_exceeded',
'Service::Quota_exceeded', and 'Root::Quota_exceeded' exceptions
by the single 'Insufficient_ram_quota' exception type.
Furthermore, the 'Parent' interface distinguished now between
'Out_of_ram' (the child's RAM is exhausted) from
'Insufficient_ram_quota' (the child's RAM donation does not suffice to
establish the session).
This eliminates ambiguities and removes the need to convert exception
types along the path of the session creation.
Issue #2398
This patch adds sanity checks to the RPC entrypoint that detect attempts
to manage or dissolve the same RPC object twice. This is not always a
bug. I.e., if RPC objects are implemented in the modern way where the
object manages/dissolves itself. As the generic framework code (in
particular root/component.h) cannot rely on this pattern, it has to
call manage/dissolve for session objects anyway. For modern session
objects, this double attempt would result in a serious error (double
insertion into the object pool's AVL tree).
Issue #2398
This patch replaces the former use of size_t with the use of the
'Ram_quota' type to improve type safety (in particular to avoid
accidentally mixing up RAM quotas with cap quotas).
Issue #2398
The 'Ram_allocator' interface contains the subset of the RAM session
interface that is needed to satisfy the needs of the 'Heap' and
'Sliced_heap'. Its small size makes it ideal for intercepting memory
allocations as done by the new 'Constrained_ram_allocator' wrapper
class, which is meant to replace the existing 'base/allocator_guard.h'
and 'os/ram_session_guard.h'.
Issue #2398
This patch augments the existing session/session.h with useful types for
the session creation:
* The new 'Insufficient_ram_quota' and 'Insufficient_cap_quota'
exceptions are meant to supersede the old 'Quota_exceeded' exception
of the 'Parent' and 'Root' interfaces.
* The 'Session::Resources' struct subsumes the information about the
session quota provided by the client.
* The boolean 'Session::Diag' type will allow sessions to operate in a
diagnostic mode.
* The existing 'Session_label' is not also available under the alias
'Session::Label'.
* A few helper functions ease the extraction of typed session arguments
from the session-argument string.
Issue #2398
This patch upgrades the cap-space slab only if the kernel runs out of
entries, instead of consuming as much PD-session quota as possible.
Until now, the behavior worked well because the cap-space slab was the
only consumer of PD-session quota. However, once we start accounting all
PD session meta data - and eventually merging the PD and RAM services -
the aggressive scheme stands in the way.
Issue #2398
This accessor is useful to eagerly expand the slab with new slab blocks,
side stepping the slab's built-in policy for the allocation of new slab
blocks.
This is particularly important when using the slab for allocating the
cap space meta-data for the base-hw kernel. To guarantee that the slab
gets never exhausted in the kernel, it is expanded before entering the
kernel.
With the introduction of the 'Out_of_caps' exception type, the slab
needs to consider exceptions during the call of '_new_slab_block' by
reverting the 'nested' state.
The old download location is very shaky resp. currently unavailable and
also other projects (e.g., Gentoo and Linux From Scratch) use this
location. Note, the archive hash does _not_ change.
By building the posix library as shared object with an ABI, we
effectively decouple posix-using programs from the library
implementation (which happens to depend on several os-level APIs such as
the VFS).
This commit moves the headers residing in `repos/base/include/spec/*/drivers`
to `repos/base/include/drivers/defs` or repos/base/include/drivers/uart`
respectively. The first one contains definitions about board-specific MMIO
iand RAM addresses, or IRQ lines. While the latter contains device driver
code for UART devices. Those definitions are used by driver implementations
in `repos/base-hw`, `repos/os`, and `repos/dde-linux`, which now need to
include them more explicitely.
This work is a step in the direction of reducing 'SPEC' identifiers overall.
Ref #2403
causes the rem timer callback pending check to run more often (every 1 ms
instead 10 ms). This is essential to met the timeout requirements of the
audio backend, which must be checked&run every 5ms.
This patch adjusts the interactive scenarios of the gems repository to
use the depot. This has three immediate benefits. First, once the depot
is populated with binary archives, the start time of the scenarios
becomes very quick because most dependency checks and build steps are
side-stepped. Second, the run scripts become more versatile. In
particular, run scripts that were formerly supported on base-linux only
(nit_fader, decorator, menu_view) have become usable on all base
platforms that have a 'drivers_interactive' package defined. Finally,
the run scripts have become much shorter.
Issue #2339
This way, files copied from the depot are incorporated in addition to
the files explicitly specified as boot modules.
The patch also adds an automatic check for the validity of the XML
syntax of boot modules ending with '.config'.
Issue #2339
Run scripts can use the new 'import_from_depot' function to incorporate
archive content from the depot into a scenario. The function must be
called after the 'create_boot_directory' function and takes any number
of pkg, src, or raw archives as arguments. An archive is specified as
depot-relative path of the form <user>/<type>/name. Run scripts may
call 'import_from_depot' repeatedly.
An argument can refer to a specific version of an archive or just the
version-less archive name. In the latter case, the current version (as
defined by a corresponding archive recipe in the source tree) is used.
If a 'src' archive is specified, the run tool integrates the content of
the corrsponding binary archive into the scenario. The binary archives
are selected according the spec values as defined for the build directory.
As of now, only x86_32 and x86_64 are supported by the 'depot_spec'
function.
Issue #2339
In order to deliver base-hw as a binary archive, we need to install the
bootstap.o file to bin/. Since bin/ is a global name space shared by all
kernels, this patch renames the object file to bootstap-hw.o and thereby
clarifies the association of the file with base-hw.
This patch replaces the set-defaults command by a reset command, which
is needed to use the Lenovo x250 trackpoint. (original patch by
Christian Prochaska)
For asynchronously provided sessions, the parent has to maintain the
session state as long as the server hasn't explicitly responded to a
close request. For this reason, the lifetime of such session states is
bound to the server, not the client.
When the server responds to a close request, the session state gets
freed. The 'session_response' implementation does not immediately
destroy the session state but delegates the destruction to a client-side
callback, which thereby also notifies the client. However, the code did
not consider the case where the client has completely vanished at
session-response time. In this case, we need to drop the session state
immediately.
Fixes#2391
Originally, the spec files for less specific SPEC values were include
via the 'select_from_repositories' function. This implies that BASE_DIR
must always be present in the list of 'REPOSITORIES'. Otherwise the
spec files won't be found. By explicitly including sub specs from
'$(BASE_DIR)/mk', we lift this restriction.
This patch is required to build the OKL4 version of core from a source
archive. It avoids fetching source codes from BASE_DIR, and moves the
vpath wildcard for %.cc after all specific vpath definitins, in
particular those that are x86-specific. Without the latter change, core
would always end up using the generic version of 'platform_services.cc',
omitting the IO_PORT service from core.
The <build-dir>/bin/ directory used to contain symbolic links to the
unstripped build results. However, since the upcoming depot tool
extracts the content of binary archives from bin/, the resulting
archives would contain overly large unstripped binaries, which is
undesired. On the other hand, always stripping the build results is not
a good option either because we rely of symbol information during
debugging.
This patch changes the installation of build results such that a new
'debug/' directory is populated besides the existing 'bin/' directory.
The debug directory contains symbolic links to the unstripped build
results whereas the bin directory contains stripped binaries that are
palatable for packaging (depot tool) and for assembling boot images (run
tool).
By installing the core object to bin/, we follow the same convention as
for regular binaries. This, in turn, enables us to ship core in a
regular binary archive. The patch also adjusts the run tool to pick up
the core object from bin/ for the final linking stage.
When creating a source archive for the USB driver, both the contrib and
Genode-specific source codes are merged into a single directory
structure. In this case, the original way of determining the Linux
source code to scan for #include directives would apply the scanning to
Genode-specific source codes too. This patch tightens the search
criterion such that only Linux source codes are processed.
This macro is implicitly pulled in by libc-setjmp (via the libc's
cdefs.h). However, apparently not all sources include <setjmp.h>.
Unfortunately, for sources that do, this change produces a
double-definition warning. We should fix it by removing the dependency
from the libc's setjmp.
File_system servers shall deny clients not matching a defined policy.
Servers shall also apply session root offset policy followed by a client
offset.
Fix#2365
Init's service forwarding functionality did not take the service type
into account when forwarding a session request. If a server provides
multiple services, e.g. fb_sdl that provides both "Input" and
"Framebuffer", the type of the forwarded session request did not always
correspond to the actually requested type.
'unzip' can uncompress and load raw multiboot images and ELF files.
Usage together with the PXE bootloader ease life running the muen hypervisor
together with a Genode/x86_64 VM, where the raw boot image is typically quite
large.
Ref #2358
The information log file contains a list of all log files that are
expected to exist after the autopilot has finished its execution.
By using the '-i' option the default filename of 'autopilot.log'
can be overriden.
Debian has dropped mkisofs long time ago, hence hardcoding it prevents
Genode from being built on Debian easily. This patch makes the tool
configurable (defaulting to mkisofs). Building on Debian can then be
done by something like:
ISOTOOL=genisoimage make run/foobar
Fixes#2234Fixes#2235
The size of the whole table and table entries were exchanged for PML4,
leading to out-of-bound accesses for addesses >= 2^39. Some constants
were lacking type suffixes causing integer overflows.
Added assertions to catch out-of-bound accesses early on.
Fixes#2210Fixes#2211
If we do the tics-to-us translation with one division and multiplication
over the whole argument, like before, we loose microseconds granularity
although the timer frequency allows for such granularity. Thus, we treat
the most significant half and the least significant half of the tics
value separate. Each half is shifted to the best bit position for the
translation, then translated, and then shifted back.
Ref #2347
The use of 'select_from_repositories' for locating the linker script for
dynamically-linked executables only works if 'BASE_DIR' appears in the
list of 'REPOSITORIES'. This is the case when using the build system in
the traditional way but it is not desired when building binary archives
of individual components.
This patch adjusts the run script in two ways:
It removes the reliance on init's formerly built-in resource-request
handling by increasing the RAM quota for the backdrop instances. Since
commit "init: explicit response to resource requests", init no longer
hands out slack memory automatically.
Second, it makes sure that the backdrop appears under the precise label
"backdrop" at nitpicker by facilitating init's label-rewriting feature.
Without explicitly setting the label to "backdrop", nitpicker observes
the label "backdrop -> backdrop" (the first part comes from init, the
second part comes from the nitpicker-session argument specified by
backdrop itself). However, the client is only considered as default
background if labeled as "backdrop" (see nitpicker's '_create_session')
implementation.
Issue #2352
The base class of Registered must provide a virtual destructor to enable
safe deletion with just a base class pointer. This requirement can be
lifted by using Registered_no_delete in places where the deletion
property is not needed.
Fixes#2331
Ldso now does not automatically execute static constructors of the
binary and shared libraries the binary depends on. If static
construction is required (e.g., if a shared library with constructor is
used or a compilation unit contains global statics) the component needs
to execute the constructors explicitly in Component::construct() via
Genode::Env::exec_static_constructors().
In the case of libc components this is done by the libc startup code
(i.e., the Component::construct() implementation in the libc).
The loading of shared objects at runtime is not affected by this change
and constructors of those objects are executed immediately.
Fixes#2332
With the current implementation resource requests are not automically
satisfied with slack quota by init. Therefore, this commit adapts RAM
quotas of autopilot scenarios to the actual demands.
An inline attribute mismatch in the gcc-4.9.2 source causes its
compilation to fail on modern gcc versions (verified with gcc 6.3.1,
but probably since gcc 5)
The patch is courtesy of the gcc-patches mailing list:
https://gcc.gnu.org/ml/gcc-patches/2015-08/msg00375.htmlFixes#2341
The test used to rely on init's formerly built-in policy of answering
resource requests with slack memory, if available. Since init no longer
responds to resource requests in an autonomous way, we use a dynamically
configured sub-init instance as runtime for the test. This instance, in
turn, is monitored and controlled such that resource requests are
result in quota upgrades. The monitoring component is implemented in
the same test-resource_request program as the test. Both roles are
distinguished by the "role" config attribute.
This is a follow-up to "init: explicit response to resource requests".
- use more upstream hm code
- add call to memory check as done in vbox4
- add in principle all vbox devices and drivers
- avoid null pointer during VM startup (patch reported to vbox-devel list)
- avoid endless loop in usb root hub
Issue #2338
This patch equips init with the ability to act as a server that forwards
session requests to its children. Session requests can be routed
depending of the requested service type and the session label
originating from init's parent.
The feature is configured by one or multiple <service> nodes hosted in
init's <config> node. The routing policy is selected by via the regular
server-side policy-selection mechanism, for example:
<config>
...
<service name="LOG">
<policy label="noux">
<child name="terminal_log" label="important"/>
</policy>
<default-policy> <child name="nitlog"/> </default-policy>
</service>
...
</config>
Each policy node must have a <child> sub node, which denotes name of the
server with the 'name' attribute. The optional 'label' attribute defines
the session label presented to the server, analogous to how the
rewriting of session labels works in session routes. If not specified,
the client-provided label is presented to the server as is.
Fixes#2247
This patch removes the formerly built-in policy of responding to
resource requests with handing out slack quota. Instead, resource
requests have to be answered by an update of the init configuration with
adjusted quota values.
Note that this patch may break run scripts that depend on init's
original policy. Those run scripts may be adjusted by increasing the
quota for the components that use to inflate their RAM usage during
runtime such that the specified quota suffices for the entire lifetime
of the component.
This patch destructs the environment sessions for the binary and the
dynamic linker along with the other environment sessions to avoid a
warning about reverting quota that occurs when attempting to close
these sessions too late.
This patch improves init's dynamic reconfigurability with respect to
adjustments of the RAM quota assigned to the children.
If the RAM quota is decreased, init withdraws as much quota from the
child's RAM session as possible. If the child's RAM session does not
have enough available quota, a resource-yield request is issued to
the child. Cooparative children may respond to such a request by
releasing memory.
If the RAM quota is increased, the child's RAM session is upgraded.
If the configuration exceeds init's available RAM, init re-attempts
the upgrade whenever new slack memory becomes available (e.g., by
disappearing other children).
Since init no longer provides public headers, we have to adjust the
existing users of this headers. The 'init/child_config.h' is used only
by GDB monitor. So the patch moves the header there as an interim fix.
The 'init/child_policy.h' is still used by a few components, so we have
to keep a trimmed-down version of it for now.
This patch enables init to apply changes of any server's <provides>
declarations in a differential way. Servers can in principle be extended
by new services without re-starting them. Of course, changes of the
<provides> declarations may affect clients or would-be clients as this
information is taken into account for the session routing.
This patch addresses the corner cases where an environment session
could not be routed, i.e., if an environment LOG log session is
routed to a non-existing child.
The optional 'version' attribute allows for the forced restart of a
child with an otherwise unmodified start node. The specified value is
also reflected in the state report.
This patch covers the resolution of the ROM route for child binaries
via the generic label-rewriting mechanics. Now, the <binary> node has
become merely sytactic sugar for a route like the following:
<start name="test"/>
<route>
<service name="ROM" unscoped_label="test">
<parent label="test-binary-name"/> </service>
...
</route>
...
</start>
A change of the binary name has an effect on the child's ROM route to
the binary and thereby implicitly triggers a child restart due to the
existing re-validation of the routing.
This patch extends the constructor of 'Local_connection' with an
optional 'label' argument, which was previously passed implicitly as
part of the 'args' argument. Keeping the label separate from 'args'
enables us to distinguish the client-specified label from a label that
resulted from a server-side label as it is used when rewriting a label
of an environment session (i.e., the binary name) in init's routing
policy. In principle, this patch eliminates the need for init's
explicite handling of the binary name via the '<binary>' node, or
at least allows us to simplity the binary-node handling.
With this check in place, one can safely construct an 'Xml_generator'
even if the report is disabled. This relieves the user of the reporter
from the need to distinguish enabled from disabled reports.
The initial ROMs (program and linker) are already attached to the region
map of a forked process and don't need to be obtained again from an
external ROM service when the 'Child' class asks for them. For the program
image, the local Noux ROM service already returned an invalid dataspace
capability, but not for the linker.
Instead of adding another 'magic' ROM name for the local ROM service,
this commit implements an 'empty' ROM service, which returns an
invalid dataspace for the initial ROMs.
Fixes#2272
The race may happen when element objects get destructed by another thread then
the thread handling the for_each loop. In this case it may happen that the
object is already destructed (left the ~Element destructor) but the thread
handling the loop touches the invalid memory afterwards (the Element lock).
detected during issue #2299Fixes#2320
Under certain timing conditions, the test would end up flushing the
input from the input filter in a nested way, which ultimately resulted
in lost input events of the outer nesting level. This patch eliminates
this corner case and thereby stabilizes the key-repeat test.
Transfer quota to the session local RAM session to react to the
Quota_exceeded exception properly.
The platform driver keeps a session local RAM session for each of its
clients that is used to allocate DMA memory. A client needs to transfer
some of its quota to the platform driver, which in return transfers this
quota to the session local RAM session. As it happens allocating memory
from a RAM session involves book keeping and in this case, where the
available quota in the session did not suffice and the request was only
a few KiB, the platform driver handled the exception wrongly and did not
transfer the quota.
This problem did not surface up to now because all drivers allocate DMA
memory in larger chunks and the book keeping overhead was of no
consequence as the initial quota transfer probably covered the overhead.
Fixes#2316.
This enables to use append_if like the append command in the following
situation.
proc optional_binary {} {...}
append_if $optional config {
<start name="} [optional_binary] {">
...
}
Due to rounding in the timeout calculation it may happen that the timeout
stored in ms becomes 0, but actually some time (us or ns) are left to wait.
With threads on various priorities (vbox) this may end up in endless loops.
Fixes#2311
The file space demand for the object files when compiling core has grown.
Therefore, the ram_fs component runs out of memory and requests additional
memory from init. On OKL4, where the physical memory is limited by the
elfweaver bootstrap tool, there is no more slack memory after the donation
of 1G to noux.
* Increase test-thread count to trigger quota exceeding on all platforms
* Synchronize test-thread destruction, otherwise an half-destructed thread
object can lead to an error message of the thread to be destructed,
which causes a deadlock, when the destructed thread still holds the log lock
* Limit SMP settings for QEMU to x86 (Ref #2307)
The signal_1/2/3 objects (which are threads) are in destruction, but still
signals are send to them. When the signal arrive and the memory for the
signal_1/2/3 object is already invalid we operate on stale memory and all
the locking infrastructure of the Thread don't work anymore.
Be more robust, explicitly wait for the termination of the thread.
Issue #2284
Otherwise it may happend that the Guest tries to set the last stored
resolution from another run, which maybe is too large.
Up to now, everthing is fine, beside the fact that output changes are not
visible - which is odd and one things the VM came not up.
Issue #2306
that happened during early bootup.
The signal about input events may arrive before keyboard and mouse is set
(due wait_and_dispatch_one_signal called from a started pthread and ep still
not done with the initialisation)
Issue #2306
Previously we had configured the timer for the Panda ES with 700 MHz
CPU clock. But the Panda A6 that we use as reference now runs with
800 MHz.
Fixes#2308
Previously, on X86, the timer driver used the PIT with a maximum timeout
of 54 ms. Thus, the driver frequently interrupted the counters with
highest priority to update the timer. This is why we needed a higher
error tolerance as for ARM where the driver, once configured, can sleep
for the whole test timeout. Now, we use the kernel timer and the problem
seems to be exits no longer.
Ref #2304
Previously we pre-calculated the translation errors for the session
quota to make a discret check in the test. But since the order, in which
init childs get their CPU quota isn't always the same anymore (we should
have never made assumptions about that) the translation errors differ
from trial to trial. However, the errors are below 0.01% of the super
period. We now tolerate them in the run script.
Ref #2304
We call curl a second time if the first check fails. This gives download
sites time to reconsider their response and helps, for example, to check
the qemu-usb port.
By separating the plain MMIO access implementation from the generic bit
and offset logic of registers, we can now use the latter also with other
types of register access like I2C. The register and MMIO front-ends have
not changed due to the separation.
Ref #2196
* Acknowledge receive of page-fault signal with ack_signal,
but restart thread execution separately
* use kill_signal_context when disolving a pager_object to prevent race
* Remove bureaucracy in form of Thread_event and Signal_ack_handler
* remove dead code in riscv, namely Thread_base definition
* translation_table_insertions function for ARM drops out,
which was overcautious
The MIN_PSK_LENGTH constant was not adjusted to accommodate for the
semcantic change when switching from using the raw char array to using
the Genode::String class. The Genode::String::length() method includes
the terminating NUL byte while strlen() does not.
Fixes#2296.
With the commit "init: session-label rewriting", the stack usage
increased due to the handling of session-label strings as local
variables. The stack overrun occurred in the vmm scenario on
base-hw.
There was a race when the component entrypoint wanted to do
'wait_and_dispatch_one_signal'. In this function it raises a flag for
the signal proxy thread to notice that the entrypoint also wants to
block for signals. When the flag is set and the signal proxy wakes up
with a new signal, it tried to cancel the blocking of the entrypoint.
However, if the entrypoint had not reached the signal blocking at this
point, the cancel blocking failed without a solution. Now, the new
Kernel::cancel_next_signal_blocking call solves the problem by storing a
request to cancel the next signal blocking of a thread immediately
without blocking itself.
Ref #2284
To select a different keyboard layout than the default 'en_us', override the
'language_chargen' function in your run script (after including
qt5_common.inc):
proc language_chargen { } { return "de" }
where "de" refers to the character map file
'repos/os/src/server/input_filter/de.chargen'
Issue #2264
This patch improves the accuracy of init's quota-saturation feature
(handing out all slack quota to a child by specifying an overly high RAM
quota for the child) and makes the RAM preserved by init configurable.
The preservation is specified as follows:
! <config>
! ...
! <resource name="RAM" preserve="1M"/>
! ...
! </config>
If not specified, init has a reasonable default of 160K (on 32 bit) and
320K (on 64 bit).
It seems that our buildbot has a problem with the TCL command 'string
cat'. In most cases it is not necessary anyway as we can use the ""
enclosure instead. It unfolds inline procedure calls and variables
automatically. We don't want to use "" only in cases where the literal
shall contain many " characters itself as it is the case for XML
configs. Then we use the 'append' command and a helper variable instead.
Ref #2193
It can happen that when Cpu_free_component is constructed the insertion
of the object through 'manage' succeeds for the EP put not for the pager
EP, which in turn raises an Out_of_meta_data exception. Because we are
within the constructor, the descstructor is not called, leading to a
dangling object pool entry for the EP.
issue #2289
This patch lets init apply configuration changes to a running scenario
in a differential way. Children are restarted if any of their session
routes change, new children can be added to a running scenario, or
children can deliberately be removed.
Furthermore, the new version of init is able to propagate configuration
changes (modifications of <config> nodes) to its children without
restarting them.
If 'close' does not call 'unlink' like 'shutdown', the Lxip_socket_dir
never gets destroyed and thus the socket server leaks resources like
RAM and ports.
Ref #2285
Our 'shutdown' implementation handles only the case that 'how' is 'RDWR'.
Thus, print an error and continue if a user calls it with another value.
Fixes#2285
If not dissolved in ~Entrypoint, the signal proxy is found within NOVA's
and FOC's object pool upon Rpc_entrypoint destruction. This leads to a
deadlock because the signal proxy is destructed before the RPC EP.
issue #2284
This patch ensures that the POLICY::release is called whenever the
session creation aborted with an exception. In the original version, an
exception like 'Quota_exceeded' caused a single-session root interface
to deny subsequent session requests.
If 'Libc::Kernel::resume:all()' is called from a non-main thread, send a
signal to unblock the main thread from 'wait_and_dispatch_one_signal()'.
Fixes#2283
Change metadata before submitting a packet. If the submitting thread is a
pthread, the metadata may be immediately change by the signal handler running
in the context of the entrypoint thread.
This patch enhances the 'Child' and 'Child_policy' with the ability to
separate the different steps of bootstrapping children. If the
'Child_policy::initiate_env_sessions()' returns false, the child's
environment sessions remain unrouted at construction time. This way,
child objects for many children can be initialized to a state that
allows the children to represent services for other children. Therefore,
session routing can be applied before any child executes.
At this stage, the environment RAM sessions of all children can be
created. Note that this step still has the limitation that RAM sessions
are generally expected to be provided by either the parent or a local
service.
Once all children are equipped with RAM, they can in principle receive
session-quota donations. Hence, all other environment sessions can now
be arbitrarily routed and initiated.
Once the environment of a child is complete, the child's process and
initial thread is created.
This patch improves the accounting for the backing store of
session-state meta data. Originally, the session state used to be
allocated by a child-local heap partition fed from the child's RAM
session. However, whereas this approach was somehow practical from a
runtime's (parent's) point of view, the child component could not count
on the quota in its own RAM session. I.e., if the Child::heap grew at
the parent side, the child's RAM session would magically diminish. This
caused two problems. First, it violates assumptions of components like
init that carefully manage their RAM resources (and giving most of them
away their children). Second, if a child transfers most of its RAM
session quota to another RAM session (like init does), the child's RAM
session may actually not allow the parent's heap to grow, which is a
very difficult error condition to deal with.
In the new version, there is no Child::heap anymore. Instead, session
states are allocated from the runtime's RAM session. In order to let
children pay for these costs, the parent withdraws the local session
costs from the session quota donated from the child when the child
initiates a new session. Hence, in principle, all components on the
route of the session request take a small bite from the session quota to
pay for their local book keeping
Consequently, the session quota that ends up at the server may become
depleted more or less, depending on the route. In the case where the
remaining quota is insufficient for the server, the server responds with
'QUOTA_EXCEEDED'. Since this behavior must generally be expected, this
patch equips the client-side 'Env::session' implementation with the
ability to re-issue session requests with successively growing quota
donations.
For several of core's services (ROM, IO_MEM, IRQ), the default session
quota has now increased by 2 KiB, which should suffice for session
requests to up to 3 hops as is the common case for most run scripts. For
longer routes, the retry mechanism as described above comes into effect.
For the time being, we give a warning whenever the server-side quota
check triggers the retry mechanism. The warning may eventually be
removed at a later stage.
This patch equips init with the ability to report its internal state in
the form of a "state" report. This feature can be enabled by placing a
'<report>' node in init's configuration.
The report node accepts the following arguments (with their default
values):
'delay_ms="100"': specifies the number of milliseconds to wait before
producing a new report. This way, many consecutive state changes -
like they occur during the startup - do not result in an overly
large number of reports but are merged into one final report.
'buffer="4K"': the maximum size of the report in bytes. The attribute
accepts the use of K/M/G as units.
'init_ram="no"': if enabled, the report will contain a '<ram>' node
with the memory stats of init.
'ids="no"': supplement the children in the report with unique IDs, which
may be used to infer the lifetime of children accross configuration
updates in the future;
'requested="no"': if enabled, the report will contain information about
all session requests initiated by the children.
'provided="no"': if enabled, the report will contain information about
all sessions provided by all servers.
'session_args="no"': level of detail of the session information
generated via 'requested' or 'provided'.
'child_ram="no"': if enabled, the report will contain a '<ram>' node
for each child based on the information obtained from the child's RAM
session.
Issue #2246
This method is a hook to enable a runtime to respond to state changes.
In particular, in init this hook is used to trigger the generation of a
new state report, if configured.
Furthermore, the patch introduces the 'generate_client_side_info' and
'generate_server_side_info' methods to the 'Session_state', which
generates an XML representation of the session states to appear in
reports produced by init.
Issue #2246
Normally, the platform driver helpers adapt the global run variables directly
via append. But the introduction of a more elegant run script style, that
incorporates dependent strings inline may be a good idea. Thus, we need the
backends of the helpers available as functions that return their string rather
than appending it.
The old interface still exists and uses the new interface as backend.
Ref #2193
The 'server_ip' and 'server_port' attributes for 'lxip/udp_client' and
'lwip/http_clnt' as well as the 'port' attribute for 'lxip/udp_echo' and
'lwip/http_srv_static' are not directly libc-related so they should not
live in the libc tag but in the config tag of the component.
Ref #2193
This patch enhances init with the support for rewriting session labels
in the target node of a matching session route. For example, a Noux
instance may have the following session route for the "home" file
system:
<route>
<service name="File_system" label="home">
<child name="rump_fs"/>
</service>
...
</route>
At the rump_fs file-system server, the label of the file-system session
will appear as "noux -> home". This information may be evaluated by
rump_fs's server-side policy. However, when renaming the noux instance,
we'd need to update this server-side policy.
With the new mechanism, the client's identity can be hidden from the
server. The label could instead represent the role of the client, or a
name of a physical resource. For example, the Noux route could be
changed to this:
<route>
<service name="File_system" label="home">
<child name="rump_fs" label="primary_user"/>
</service>
...
</route>
When the rump_fs receives the session request, it is presented with the
label "primary_user". The fact that the client is "noux" is not taken
into account for the server-side policy selection.
Issue #2248
The new return value of 'resolve_session_request' allows the child
policy to define the label used as the policy selector at the server.
Because this patch introduces the distinction of the child-provided
label from the label as presented to the server along with the session
request, the latter is now handled as a dedicated 'Session_state'
argument.
Issue #2248
This commit includes changes to the Nic::Session_component interface.
We now pass the entire env to the component instead of only ram, rm and
the ep because we need the env to open connections from within the
Session_component implemenation. So far only the cadence_gem driver
needs this, though.
Issue #2280.
Libc components cannot use regular calls to select() as this may suspend
their execution. In this case incoming RPCs will be deferred until
select() returns and the component returns to the entrypoint dispatch
loop. The Libc::Signal_handler solves this problem with a its select()
that either returns the currently ready file descriptors immediately or
calls the registered handler function during libc resume.
Now, the libc kernel supports to execute application code from all RPC
functions not only Component::construct(). This is enabled by the
Libc::with_libc() scope function.
This commit extends an easy-to-use mechanism to allow Genode component
code to enter/leave the libc application context. This is needed
whenever low-level component code (like signal handlers or RPC
functions) need to interact with potentially blocking libc I/O
functions.
Please note that this commit contains the API-level design only. The
actual context switching code 'execute_in_application_context' is
missing.
The socket file system can be configured in the "socket" attribute of
the libc config node like follows.
<vfs> <dir name="socket"> <fs/> </dir> </vfs>
<libc ... socket="/socket"/>
This configures the socket file system libc backend to access files in
"/socket" for socket operations.
There existed a race when 'wait_and_dispatch_one_signal' is called form
a RPC context, because the 'signal_proxy' or 'main' will block and the
signal semaphore, when the EP then calls 'wait_and_dispatch_one_signal',
the signal proxy is woken up ands sends an RPC to the EP, leading to a
dead lock if no further signal arrive, because the EP will then remain
blocked in the signal semaphore.
Therefore, for this case, the signal proxy will now perform a semaphore
up operation and does not perform an RPC if the EP is within
'wait_and_dispatch_one_signal'.
This patch enhances init with the ability to route individual
environment sessions. Prior this patch, environment sessions could be
routed only by an all-encompassing '<service>' node that would match
both child-initiated and environment sessions.
In contrast to the existing 'label', 'label_prefix', and 'label_suffix'
attributes of '<service>' nodes, which are always scoped with ther name
of the corresponding child, the 'unscoped_label' allows the definition
of routing rules for all session requests, including init's requests for
the child's environment sessions. For example, to route the ROM session
requests for a child's dynamic linker, the following route would match:
<route>
<service name="ROM" unscoped_label="ld.lib.so"> ... </service>
</route>
Issue #2215
When a directory gets destructed it dissolves the handles of each contained file
but the acknowledgement might be still in-flight. If we finally receive it,
it leads to an Unknown_id exception on the Handles ID Space in 'handle_ack'.
Now we catch it, print a warning, and go on.
This patch adds the handling of 'CHARACTER' events as emitted by the
input-filter's character generator (<chargen>). To avoid interpreting
press/release events twice (at the input filter and by the terminal's
built-in scancode tracker), the terminal's scancode tracker can be
explicitly disabled via <config> <keyboard layout="none"/> </config>.
In the future, the terminal's built-in scancode tracker will be
removed.
The use of the terminal with the input filter is illustrated by the
'terminal_echo.run' script.
Issue #2264
The input_filter is the successor of the input_merger. In addition to
merging input streams, the component applies several forms of input
transformations such as the application of keyboard layouts.
Issue #2264
Character events are created via a dedicated 'Event' constructor that
takes an 'Event:Utf8' object as argument. Internally, the character is
kept in the '_code' member. The 'Utf8' value can by retrieved by the
recipient via the new 'utf8' method.
Issue #2264
A binary file may be a temporary Vim .swp file when examining contrib
sources. The commit prevents build errors like
.../repos/dde_linux/lib/mk/lxip_include.mk:29:
target '.../x86_64/var/libcache/lxip_include/include/include/include/Binary'
given more than once in the same rule
.../repos/dde_linux/lib/mk/lxip_include.mk:29:
target '.../x86_64/var/libcache/lxip_include/include/include/include/file'
given more than once in the same rule
...
A Signal_handler may schedule a hook function that is executed after the
signal handler returned. This can be used if the hook function may
trigger a (nested) signal handler by means of
wait_and_dispatch_one_signal(). Otherwise, an occurrence of the same
signal that triggered the original signal handler results in a dead lock
just before calling the nested handler (due to the Signal_context
destruction lock).
The read-ready packet informs the server that the client wants to be
notified if a handle becomes readable. When becoming readable, the
server acknowledges packet and the client may queue a read requests
accordingly.
The i.MX53 Framebuffer driver doesn't come up on on Fiasco.OC because the Platform
driver isn't allowed to access essential devises like the SRC or the Fuses. This is
most likely due to the kernel not configuring the CSU appropriately.
Ref #2268
broken due to changes of
libc: API transition
Issue #1987
For now provide a initial memory buffer for allocation of static
constructors and of malloc calls out of the libc during early
libc initialization until actual vbox code is executed having the Env
pointer.
This change introduces a Genode specific init function, which sets the
backend allocator used by jent_zalloc/zfree(). As consequence the
library can solely be used by native Genode components, direct libc
usage is not supported.
Fixes#2274.
Put the initialization of the cpu cores, setup of page-tables, enabling of
MMU and caches into a separate component that is only used to bootstrap
the kernel resp. core.
Ref #2092
Instead of implicitly asking for core's link address when linking
core within the run tool, deliver it explicitly to the build_core
routine. Thereby we gain the freedom to use the build_core tool for
different targets like core, and bootstrap.
Ref #2092
This hook allows the export of the allocator's state by a derrived
class. I.e., the final state of the allocator used for bootstrapping
core.
Ref #2092
This patch eliminates the need for a global allocator by passing the
parent-service registry as argument to the 'Slave::Policy' constructor.
Fixes#2269
The support has two parts. First, a VFS plugin now gets passed an
I/O-response handler callback on construction, which informs users of the
VFS that an I/O event occurred. This enables, for example, the libC to
check if blocking read can be completed. Further, the VFS file I/O
interface provides now functions for suspendable reads, i.e.,
queue_read() and complete_read().
Replacing the node lookup table with an Id_space removes the
limit on open handles per session and allows mutal associativity
between File_system handles and local VFS handles.
Fix#2221
The test now forks twice - the parent forks a child and the child itself
forks a grand child. Both, parent and child, wait for termination of
their forked process with waitpid(). Additionally, the run script now
checks for exit of the parent (not any noux process).
First, calls to manage and dissolve signal contexts now check if the
signal receiver was constructed. There is a small window during suspend
where it is destructed before reconstructed again.
Last, we ensure that processing of incoming signal was deblocked by the
suspend signal before entering the suspend operation. This way we ensure
already queued signal are handled.
The block file system wrongly modified the seek offset during a
read-modify-write operation that is required for sub-block-size
requests. This led to problems whenever such write requests spanned
multiple blocks and thereby were handled in multiple iterations.
Fixes#2262
This test reproduces an issue of the VFS block file system when the
underlying block device has a coarser granularity than the block
requests issued by the VFS client. I.e., if the underlying block device
has a block size of 4K, writing a sequence of (non-4K-aligned) 512 blocks
that crosss a 4K boundary corrupts the data on the block device.
Issue #2262
The new utility at 'os/static_parent_services.h' allows the creation of
a registry of parent services at compile time and thereby eliminates the need
for dynamic memory allocations whenever the set of services is known at
compile time as is the case for most uses of 'Slave::Policy'. The commit
showcases the utility in the bomb test.
This commit enables compile-time warnings displayed whenever a deprecated
API header is included, and adjusts the existing #include directives
accordingly.
Issue #1987
On Odroid XU the SD card driver comes up and finds a card but for card
access it seems that we would need a platform driver like on Arndale.
On imx_53, the first SDHCI MMIO access faults. This is likely due to the
AIPSTZ memory bridge. On HW, we initialize the AIPSTZ in the kernel, but
when I tried doing that in the platform driver instead, the first AIPSTZ
MMIO access faults ^^ So I gave up for now and removed support.
Fixes#2259
Parse ``<env key="..." value=".."/>`` nodes from the config ROM and
populate a list at the 'genode_envp' and 'environ' symbols.
Test script at run/libc_getenv.
Fix#2236
In combination with run/image/uboot, run/boot_dir/foc expected a file link it
created itself to be a directory by trying to create another file link inside
it.
Ref #1987
For all tests
* use Component::construct instead of main
* use new connection constructors with env argument
* use log instead of printf
For some tests
* replace signal receivers with signal handlers
* replace global static variables with Main class members
* remove unnecessary multithreading
* model test steps as classes that are independent from each other and managed
by Main as constructibles
* use references instead of pointers and exceptions instead of error codes
* use Attached_* helpers intead of doing attach/detach manually
* use helpers like String, Id_space, Registry instead of arrays and lists
* make the run script suitable for automated execution and conclusion
Ref #1987
In the past, the Genode::destroy, that is called by the RAM-FS-chunk destructors,
issued Allocator::free instead of the C++ delete. Therefore it was possible to
use the size argument of Allocator::free for the allocation tracker in the
RAM-FS-chunk test. Nowadays, we have to keep track of the allocation sizes
ourselves because delete doesn't hand over the size.
Ref #1987
The FB Block Adapter in os/src/test visualizes a block session via a
Framebuffer session. As far as I can see, it is not a test but rather
the base for a bump-in-the-wire component. However, for this role it
currently lacks a Block back-end. As it also would have to be updated to
use the new base API I removed it instead, leaving only its git
history as inspiration if someone needs such a component in the future.
Fixes#2245
Ref #1987
lesskey and lessecho missed the declaration of ${LIBS} on the compiler
command line, which ended up in unusable programs.
> file noux-pkg/less/lesskey.broken
noux-pkg/less/lesskey.broken: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), dynamically linked, interpreter *empty*, not stripped
> file noux-pkg/less/lesskey
noux-pkg/less/lesskey: ELF 32-bit LSB executable, Intel 80386, version 1 (SYSV), dynamically linked, interpreter ld.lib.so, not stripped
The issue was identified because -O0 builds broke with
ld: lesskey: The first section in the PT_DYNAMIC segment is not the .dynamic section
Unfortunately, this simple fix renders both tools also dependent to libm
and ncurses which they don't use.
This streamlines the Genode-specific interface for both 32-bit and
64-bit architectures and fixes dynamic-linking issue with the rump
VFS due to differing size_t types.
This function returns the information whether the used platform relies
on USB HID for interactive scenarios by default as is the case for most
ARM platforms. In contrast, for x86 the USB driver can be omitted because
we can use the PS/2 driver (that is readily available in repos/os/).
If the detach address is not the beginning of the region, one gets:
"virtual void Genode::Allocator_avl_base::free(void*): given
address (0x180e0) is not the block start address (0x18000)"
Instead, print an explicit warning in front of the detach call.
Cleaning up LWIP when returning from the main function sporadically
leads to endless errors "Error: sys_arch_mbox_fetch: unknown exception
occured!". We let the client sleep forever at the end of its main function
to prevent tests from failing due to a flooded log.
Reg #2193
* get rid of printf
* use exceptions instead of error codes
* use Id_space instead of the individual block device registry
* use Cstring instead of char const*
* move method definitions > 1 line to .cc files
* rename Block Block_driver and Serial Serial_driver to avoid name clashes
with the Genode namespace and thereby simplify the code
* use lambdas for Block device lookup and apply
* switch to the Component framework
* don't use env(), config(), ... and hand over env to each connection
* use Attached_mmio and Attached_rom/ram_dataspace instead of manual
solutions
Fixes#2223
The init component used to create the CPU/RAM/PD/ROM sessions (the child
environment) for its children by issuing session requests to its parent,
which is typically core. This policy was hard-wired. This patch enables
the routing of the environment sessions of the children of init
according to the configured routing policy.
Because there is no hard-wired policy regarding the environment sessions
anymore, routes to respective services must be explicitly declared in
the init configuration. For this reason, the patch adjusts several run
scripts in this respect.
This patch removes the outdated '<if-args>' special handling of session
labels. The '<if-args>' feature will eventually be removed completely
(ref #2250)
Issue #2197
Issue #2215
Issue #2233
Issue #2250
This patch changes the 'Xml_node_label_score' to regard an empty
label_prefix or label_suffix as a match instead of a conflict. Until
now, there was no use case for an empty label_prefix. But with init's
new ability to route environment sessions, an empty prefix denotes any
child-initiated session (as oposed to an parent-initiated environment
session).
Issue #2215
Issue #2233
This patch fixes a problem that unsurfaced by the commit "menu_view: API
transition", which changed the class layout of the 'Png_image' so that
the 'Read_struct' pointer is no longer equal to the 'Png_image' pointer.
This commit addresses the situation where an environment session
outlives the session-providing service. In this case, the env session
got already invaidated at the destruction time of the server. However,
the underlying session-state structure continues to exist until the
client is destructed. During the eventual destruction of such a dangling
environment session, we have to be careful not to interact with the
no-longer existing service.
Ref #2197
This patch addresses the corner case of destructing a child that
provides an enviroment session to another child. Before this patch,
this situation could result in an infinite loop.
The problem was introduced as a side effect of issue #2197 "base: apply
routing policy to environment sessions".
This patch re-enables the launchpad to start multiple instances of the
same program. Without it, launchpad wrongly requests the binary ROM with
the child's unique name as label. The lookup of the first instance
solely succeeds because the unique name equals the binary name.
To better support non-blocking terminal components, let the
'Terminal::Session::write()' function return the number of bytes
actually written.
Fixes#2240
The session-control mechanism is based on the way how sessions are
labeled. In #2171, we changed the labeling to be more strict. In
particular, label-less sessions do no longer exist.
Unfortunately, nitpicker and the window manager still handled the former
weaker labeling, which ultimately led to a situation where any
session-control argument would mismatch. The behavior could be observed
in the launcher.run script where a click on the subsystem button would
not focus the clicked-on subsystem. With the patch, the scenario works
again as expected.
This patch enables warnings if one of the deprecate functions that rely
in the implicit use of the global Genode::env() accessor are called.
For the time being, some places within the base framework continue
to rely on the global function while omitting the warning by calling
'env_deprecated' instead of 'env'.
Issue #1987
This patch removes the dependency of the deprecated Genode API,
fixes the coding style, and removes the "random" file system
(superseded by the VFS plugin mechanism).
Ref #1987
Merge the platform-specific files and classes (they merely aggregated
themselves) so that each platform provides merely one class
Sd_card::Driver. Also, the Sd_card::Driver_base class is introduced for
the generic parts of Sd_card::Driver.
Ref #2206
Most implementations use a Signal_handler now to acknowledge the packet
instead of waiting for the transfer completion. The exceptions to that are
the non-DMA implementations for RPI and PL180
Ref #2206
In addition to that we now busy wait, i.e. poll, for interrupts
instead of using the IRQ session. That is fine because interrupts
were only used while configuring the HDMI over I2C and are not used
while normal operation.
Issue #1987.
Libc::Env is the Genode::Env interface extended to cover access
to the XML content of the 'config' ROM and a VFS instance. This
deduplicates the burden of components to attain and manage
these resources.
Fix#2217
Ref #1987
This aspect was always enabled when creating a build directory for hw,
but is not enabled anymore due to recent build directory unifications.
On the other hand it is needed for jitter entropy anyway.
Ref #2190
This commit mostly removes the globally visible NR_OF_CPUS define
from the global makefile specifiers defined in the base-hw repository.
Whereever necessary it adds platform specific makefiles to the base
repository when they were missing.
Ref #2190
This patch make the ABI mechanism available to shared libraries other
than Genode's dynamic linker. It thereby allows us to introduce
intermediate ABIs at the granularity of shared libraries. This is useful
for slow-moving ABIs such as the libc's interface but it will also
become handy for the package management.
To implement the feature, the build system had to be streamlined a bit.
In particular, archive dependencies and shared-lib dependencies are now
handled separately, and the global list of 'SHARED_LIBS' is no more.
Now, the variable with the same name holds the per-target list of shared
libraries used by the target.
Ubuntu provides position independent shared objects for libraries, e.g.,
libsdl1.2-dev. To appropriatly link it to Genode, the linker flag
'-no-pie' has to be added to the make file.
This patch removes the component_entry_point library, which used to
proved a hook for the libc to intercept the call of the
'Component::construct' function. The mechansim has several shortcomings
(see the discussion in the associated issue) and was complex. So we
eventually discarded the approach in favor of the explicit handling of
the startup.
A regular Genode component provides a 'Component::construct' function,
which is determined by the dynamic linker via a symbol lookup.
For the time being, the dynamic linker falls back to looking up a 'main'
function if no 'Component::construct' function could be found.
The libc provides an implementation of 'Component::construct', which
sets up the libc's task handling and finally call the function
'Libc::Component::construct' from the context of the appllication task.
This function is expected to be provided by the libc-using application.
Consequently, Genode components that use the libc have to implement the
'Libc::Component::construct' function.
The new 'posix' library provides an implementation of
'Libc::Component::construct' that calls a main function. Hence, POSIX
programs that merely use the POSIX API merely have to add 'posix' to the
'LIBS' declaration in their 'target.mk' file. Their execution starts at
'main'.
Issue #2199
On a 64-bit system, enabling the OpenSSL NIST 64-bit optimization should
result in considerable speed improvements when using curves: NIST-P224,
NIST-P256, and NIST-P521. Additionally it avoids that Tor complains
about having an OpenSSL that lacks this feature.
Ref #2193
These functions are marked as always inline through the 'SELF_RELOC' macro. This
became necessary because on riscv functions calls are performed through the
global offset table, which is not initialized at this point.
Fixes#2203
This commit adds support for testing multiple kernels within the same
build directory. In addition to the existing -p arguments, the new
version expects one or more -k arguments that denote the kernels to be
used for executing the specified run scripts.
Consequently, the autopilot executes the 3-dimensional matrix of
platforms x kernels x run scripts, e.g.,
autopilot --force -p x86_32 -k nova -k okl4 -k sel4 -k linux -r log
Issue #2190
This patch makes the benefit of the recently introduced unified Genode
ABI available to developers by enabling the use of multiple kernels from
within a single build directory. The create_builddir tool has gained a
new set of kernel-agnostic platform arguments such as x86_32, or panda.
Most build targets within directories are in principle compatible with
all kernels that support the selected hardware platform. To execute a
scenario via the run tool, one has to select the kernel to use by
setting the 'KERNEL' argument in the build configuration
(etc/build.conf). Alternatively, the 'KERNEL' can be specified as
command-line argument of the Genode build system, e.g.:
make run/log KERNEL=nova
This allows us to easily switch from one kernel to another without
rebuilding any Genode component except for the very few kernel-specific
ones.
The new version of the 'create_builddir' tool is still compatible with
the old version. The old kernel-specific build directories can still be
created. However, those variants will eventually be removed.
Note that the commit removes the 'ports-foc' repository from the
generated 'build.conf' files. As this is only meaningful for 'foc',
I did not want to include it in the list of regular repositories (as
visible in a 'x86_32' build directory). Hence, the repository must
now be manually added in order to use L4Linux.
Issue #2190
This patch removes the manually maintained symbol map from the dynamic
linker. This way, the symbol map stays in sync with the ABI and - more
importantly - no longer uses wildcards. So the symbols exported by the
dynamic linker are strictly limited by the ABI.
Issue #2190
Previously, if a packet should be routed to a domain that had no interface
connected, the NIC router only printed "Unroutable packet". Technically,
this was wrong as an unavailable interface doesn't mean that the routing
failed. Now it gives an error "no interface connected to domain".
Ref #2193
The main window must be visible before avplay or a framebuffer filter
requests the framebuffer session which goes to Nitpicker, because the
parent view of the new Nitpicker view is part of the
QNitpickerPlatformWindow object, which is created when the main window
becomes visible. If this object does not exist yet, a page fault occurs.
Fixes#2187
This patch changes the child-construction procedure to allow the routing
of environment sessions to arbitrary servers, not only to the parent.
In particular, it restores the ability to route the LOG session of the
child to a LOG service provided by a child of init. In principle, it
becomes possible to also route the immediate child's PD, CPU, and RAM
environment sessions in arbitrary ways, which simplifies scenarios that
intercept those sessions, e.g., the CPU sampler.
Note that the latter ability should be used with great caution because
init needs to interact with these sessions to create/destruct the child.
Normally, the sessions are provided by the parent. So init is safe at
all times. If they are routed to a child however, init will naturally
become dependent on this particular child. For the LOG session, this is
actually not a problem because even though the parent creates the LOG
session as part of the child's environment, it never interacts with the
session directly.
Fixes#2197
This patch removes possible ambiguities with respect to the naming of
kernel-dependent binaries and libraries. It also removes the use of
kernel-specific global side effects from the build system. The reach of
kernel-specific peculiarities has thereby become limited to the actual
users of the respective 'syscall-<kernel>' libraries.
Kernel-specific build artifacts are no longer generated at magic places
within the build directory (like okl4's includes, or the L4 build
directories of L4/Fiasco and Fiasco.OC, or the build directories of
various kernels). Instead, such artifacts have been largely moved to the
libcache. E.g., the former '<build-dir>/l4/' build directory for the L4
build system resides at '<build-dir>/var/libcache/syscall-foc/build/'.
This way, the location is unique to the kernel. Note that various tools
are still generated somewhat arbitrarily under '<build-dir>/tool/' as
there is no proper formalism for building host tools yet.
As the result of this work, it has become possible to use a joint Genode
build directory that is usable with all kernels of a given hardware
platform. E.g., on x86_32, one can now seamlessly switch between linux,
nova, sel4, okl4, fiasco, foc, and pistachio without rebuilding any
components except for core, the kernel, the dynamic linker, and the timer
driver. At the current stage, such a build directory must still be
created manually. A change of the 'create_builddir' tool will follow to
make this feature easily available.
This patch also simplifies various 'run/boot_dir' plugins by removing
the option for an externally hosted kernel. This option remained unused
for many years now.
Issue #2190
The header is foc-specific. It used to shadow the generic one provided
by the base repository, which contradicts with the kernel-agnostic
Genode API. Hence, it had to be moved to a foc-specific location.
This patch decouples the kernel-specific implementation of the dynamic
linker from its kernel-agnostic binary interface. The name of the
kernel-specific dynamic linker binary now corresponds to the kernel,
e.g., 'ld-linux.lib.so' or 'ld-nova.lib.so'. Applications are no longer
linked directly against a concrete instance of the dynamic linker but
against a shallow stub called 'ld.lib.so'. This stub contains nothing
but the symbols provided by the dynamic linker. It thereby represents
the Genode ABI.
At system-integration time, the kernel-specific run/boot_dir back ends
integrate the matching the kernel-specific variant of the dynamic linker
as 'ld.lib.so' into the boot image.
The ABI symbol file for the dynamic linker is located at
'base/lib/symbols/ld'. It contains the joint ABI of all supported
architectures. The new utility 'tool/abi_symbols' eases the creation of
such an ABI symbol file for a given shared library. Its result should be
manually inspected and edited as needed.
The patch removes the 'syscall' library from 'base_libs.mk' to avoid
polluting the kernel-agnostic ABI with kernel-specific interfaces.
Issue #2190
Issue #2195
By not placing the sysio buffer (16 KiB) on the stack, we can call
'noux_syscall' from the initial thread. This is needed to issue fork
from the suspend callback, which is executed by the initial thread.
This cleans up the syscalls that are mainly used to control the
scheduling readiness of a thread. The different use cases and
requirements were somehow mixed together in the previous interface. The
new syscall set is:
1) pause_thread and resume_thread
They don't affect the state of the thread (IPC, signalling, etc.) but
merely decide wether the thread is allowed for scheduling or not, the
so-called pause state. The pause state is orthogonal to the thread state
and masks it when it comes to scheduling. In contrast to the stopped
state, which is described in "stop_thread and restart_thread", the
thread state and the UTCB content of a thread may change while in the
paused state. However, the register state of a thread doesn't change
while paused. The "pause" and "resume" syscalls are both core-restricted
and may target any thread. They are used as back end for the CPU session
calls "pause" and "resume". The "pause/resume" feature is made for
applications like the GDB monitor that transparently want to stop and
continue the execution of a thread no matter what state the thread is
in.
2) stop_thread and restart_thread
The stop syscall can only be used on a thread in the non-blocking
("active") thread state. The thread then switches to the "stopped"
thread state in wich it explicitely waits for a restart. The restart
syscall can only be used on a thread in the "stopped" or the "active"
thread state. The thread then switches back to the "active" thread state
and the syscall returns whether the thread was stopped. Both syscalls
are not core-restricted. "Stop" always targets the calling thread while
"restart" may target any thread in the same PD as the caller. Thread
state and UTCB content of a thread don't change while in the stopped
state. The "stop/restart" feature is used when an active thread wants to
wait for an event that is not known to the kernel. Actually the syscalls
are used when waiting for locks and on thread exit.
3) cancel_thread_blocking
Does cleanly cancel a cancelable blocking thread state (IPC, signalling,
stopped). The thread whose blocking was cancelled goes back to the
"active" thread state. It may receive a syscall return value that
reflects the cancellation. This syscall doesn't affect the pause state
of the thread which means that it may still not get scheduled. The
syscall is core-restricted and may target any thread.
4) yield_thread
Does its best that a thread is scheduled as few as possible in the
current scheduling super-period without touching the thread or pause
state. In the next superperiod, however, the thread is scheduled
"normal" again. The syscall is not core-restricted and always targets
the caller.
Fixes#2104
The main thread does no longer execute application code. It is solely
responsible for the initialization of the component's entrypoint and for
retrieving asynchronous notifications. Since the stack usage is no
longer dependent on application-specific code, we can significantly
shrink it to reduce the memory footprint of components. In the worst
case - should the stack overrun - we would observe a page fault because
the stack is placed in the stack area, surrounded by guard pages.
This patch replaces the former machine-word-dependent default stack size
by the fixed value of 64 KiB which should suffice for components on both
32 and 64 bit. Previously, the default stack size on 64 bit was 128 KiB,
which is wasteful. If a component needs more stack than 64 KiB, it can
specify a custon stack size by implementing 'Component::stack_size'.
The initial stack is solely used to initialize the Genode environment
along with the application stack located in the stack area. It never
executes application code. Hence, we can make it small. To check that it
is not dimensioned too small, the patch introduces a sanity check right
before switching to the application stack.
At least on foc_x86_64, nic_router refused to create sessions for the
test clients as the session object's size exceeds the old quota
donation.
Ref #2139
Both methods are now available for Ipv4_address as well as for
Ipv4_address_prefix. An IPv4 address is invalid if it contains zeros only.
An IPv4 address prefix is invalid if its address is invalid and its
prefix is 32.
Ref #2139
Instead of creating one socket and re-using it each test run because the
client shall also test the termination of pseudo-connections at components that
implement hole punching for UDP.
Ref #2139
This patch unconditionally applies the labeling of sessions and thereby
removes the most common use case of 'Child_policy::filter_session_args'.
Furthermore, the patch removes an ambiguity of the session labels of
sessions created by the parent of behalf of its child, e.g., the PD
session created as part of 'Child' now has the label "<child-name>"
whereas an unlabeled PD-session request originating from the child
has the label "<child-name> -> ". This way, the routing-policy of
'Child_policy::resolve_session_request' can differentiate both cases.
As a consequence, the stricter labeling must now be considered wherever
a precise label was specified as a key for a session route or a server-
side policy selection. The simplest way to adapt those cases is to use a
'label_prefix' instead of the 'label' attribute. Alternatively, the
'label' attribute may used by appending " -> " (note the whitespace).
Fixes#2171
The log plugin can now be configured to request a log session with the
specified label like follows.
<log label="..."/>
Per default, no new log session is requested but the existing log
session of the component's environment is used.
The heap typically first tries to allocate larger chunks than necessary, and
if it fails the actual minimal one. The first attempt already triggers warnings
which are not critical at all. If the second (critical) allocation fails,
then there are additionally checks and warnings already in place.
Issue #1039
Trace_control dataspace gets destroyed implicitly when the cpu session is
closed. Remove the trace control dataspace from the internal noux dataspace
registry before cpu session destruction.
The code in Core's Cpu_session_component::create_thread might throw a
capability refernce-count overflow if one creates many threads, which would
kill core if not handled.
Ref #2120
This patch adjusts the various users of the 'Child' API to the changes
on the account of the new non-blocking parent interface. It also removes
the use of the no-longer-available 'Connection::KEEP_OPEN' feature.
With the adjustment, we took the opportunity to redesign several
components to fit the non-blocking execution model much better, in
particular the demo applications.
Issue #2120
This is a redesign of the root and parent interfaces to eliminate
blocking RPC calls.
- New session representation at the parent (base/session_state.h)
- base-internal root proxy mechanism as migration path
- Redesign of base/service.h
- Removes ancient 'Connection::KEEP_OPEN' feature
- Interface change of 'Child', 'Child_policy', 'Slave', 'Slave_policy'
- New 'Slave::Connection'
- Changed child-construction procedure to be compatible with the
non-blocking parent interface and to be easier to use
- The child's initial LOG session, its binary ROM session, and the
linker ROM session have become part of the child's envirenment.
- Session upgrading must now be performed via 'env.upgrade' instead
of performing a sole RPC call the parent. To make RAM upgrades
easier, the 'Connection' provides a new 'upgrade_ram' method.
Issue #2120
This data structure is meant as a safe alternative for a list wherever
the list is solely used to remember objects and iterate through them in
an unspecified order. One use case is the 'Service_registry'.
This data structure allows the association of objects with IDs. IDs are
kept in an AVL tree. So in contrast to a bit allocator, the ID space can be
sparsely populated and does not need to be dimensioned. The lifetime of
an ID is bound to an 'Element' object, which relieves the programmer
from manually allocating/deallocating IDs for objects.
Issue #2120
We preserve lower RAM for device drivers with physical memory
constraints. If no physical RAM constraint exists, the allocations above
3G (32-bit) or 4G (64-bit) are preferred.
Limit the number of generations to 4 to prevent hitting the
socket-descriptor limit on Linux. Also, all possible configuration
parameters for bomb our now customizable in the run script and the
current config is logged by bomb master.
The 'connected_scan_interval' config attribute specifies the scan
interval in seconds. The commit also removes the deprecated ram_fs
component from the test run script.
VirtualBox mainly derives the initial link-state for its device models
from checking the <Adapter ... cable="true"/> attribute. Our backend
only propagates the current state of the Nic session if it receives a
link-state signal. This may lead to problems if a guest detects a link
up state when it is actually down and wants to use the interface. The
backend now queries the Nic session and sets the link-state accordingly
when it is constructed.
In case there is no link do not attempt to submit a packet to the packet
stream but return with an error so that upper layers can handle it.
Enable signals for network on poweron and not already during
construction. The network model may be not yet ready to process incoming
signals and data.
Fixes#2117.
This fixes a regression on Ubuntu 16.04 (resp. Linux systems with recent
kernel versions) and address-space randomization originating from an
uninitialized relocation base of 0.
This patch is a preparation of the forthcoming async parent interface.
Note that this patch increases the size of connection objects.
Furthermore it adds a diagnostic message whenever a connection fails.
Issue #2166
Because of the session-argument buffering added to 'Connection' objects
when changing the parent interface to be non-blocking, the
'Device_component' has grown in size from 1.5 KiB to 5 KiB. The slab
allocator was configured with a block size of 4 KiB. So it does not work
with the grown 'Device_component' size.
Once the transition to the new API is completed (when we can remove the
buffering of session arguments from the 'Connection' objects), we may
revert this change.
Issue #2120
Unfortunately, the volatile object does not inherit the noncopyable
attribute of the enclosed object. By making all volatile objects
noncopyable, we prevent the accidental copying of a noncopyable object
wrapped in a volatile object.
This feature is not compatible with the forthcoming nonblocking parent
interface. The patch removes the use of feature in all places except for
the components of the demo repository, which will under go a redesign
anyway.
Issue #2120
Issue #2165
Replace 'dump()' debug utilities within Allocator_avl with Output::print
equivalents, and use the new Avl_tree::for_each utility to simplify
the implementation.
Ref #2159
Instead of using a somewhat incomplete module_param_named() macro,
which will influence other drivers, patch the driver that requires
this treatment.
Fixes#2169Fixes#2155
This overload covers the common case for initializing a string from a
literal without employing the 'Output' mechanism. This way, such
strings can by constructed without calling virtual functions, which in
turn makes the 'String' usable for the 'init_rtld' phase of the dynamic
linker.
This patch fixes a race condition triggered by the thread test running
on Linux inside VirtualBox. The 'test_stack_alloc' sporadically produced
one of two errors: A segfault in the 'Thread::deinit_platform_thread' on
the attempt to access the 'native_thread' of the to-be-destructed thread
(this data structure is located on the thread's stack). Or, an error
message about a region conflict within the stack area.
The problem was that two instances of 'Region_map_mmap' issued a
sequence of munmap and mmap each. Even though each instance locked the
attach/detach operations, the lock was held per instance. In a situation
where two instances performed attach/detach operations in parallel, the
syscall sequences could interfere with each other.
In the test scenario, the two region-map instances are the test's
address space and the stack area. When creating a thread, the thread's
trace-control dataspace is attached at an arbitrary place (picked by
the Linux kernel) within the address space whereas the stack is attached
at the stack area. The problem is the following sequence:
Thread A wants to destruct a thread:
1. Remove stack from stack area
(issue unmap syscall)
2. Preserve virtual address range that was occupied from the stack
so that Linux won't use it
(issue mmap syscall)
Thread B wants to construct a thread:
1. Request trace-control dataspace from CPU session
2. Attach trace-control dataspace to address space at a location
picked by the Linux kernel
(issue mmap syscall)
The problem occurs when thread B's second step is executed in between
the steps 1 and 2 of thread A and the Linux kernel picks the
just-unmapped address as the location for the new trace-control mapping.
Now, the trace control dataspace is mapped at the virtual address that
was designated for the stack of the to-be-created thread, and the
attempt to map the real stack fails.
The patch fixes the problem by replacing the former region-map-local
locks by a component-global lock.
Furthermore, it cleans up core's implementation of the support function
for the region-map-mmap implementation, eliminating the temporary
unlocking of the region-map lock during RPC.
Prepared for internal test machine, which has 8 logical cores.
6 Win7 64bit VMs are started, each having 2 vCPUs, using the same image and
different overlays. Changes to the VM are written to the overlays of ram_fs
and dropped after the test.
lCPU 0 : Genode base system and drivers
lCPU 1-2: VM1 2 vCPUs
lCPU 2-3: VM2 "
lCPU 3-4: VM3 "
lCPU 4-5: VM4 "
lCPU 5-6: VM5 "
lCPU 6-7: VM6 "
Fixes#2143
drm_framebuffer_remove takes care of references to CRTC pointers before
freeing up framebuffer object. Directly calling the destroy function may cause
dangling CRTC pointers pointing inside the framebuffer object.
Fixes#2140
Instead of solving the problem to deliver ROM modules to core while booting
differently for the several kernels (multi-boot, elfweaver, core re-linking),
this commit unifies the approaches. It always builds core as a library, and
after all binaries are built from a run-script, the run-tool will link an
ELF image out of the core-library and all boot modules. Thereby, core can
access its ROM modules directly.
This approach now works for all kernels except Linux.
With this solution, there is no [build_dir]/bin/core binary available anymore.
For debugging purposes you will find a core binary without boot modules, but
with debug symbols under [run_dir].core.
Fix#2095
The usb_drv must always check the device pointer in all session facing.
methods. A errorneous client can otherwise trigger a page-fault in the
driver.
Fixes#2133.
- use the correct memory free functions on errors
- report packet submit errors
- rename 'Usb::Packet_descriptor::transfer.timeout' as
'Usb::Packet_descriptor::transfer.polling_interval'
Fixes#2135
base generic code:
* Remove unused verbosity code from mmio framework
* Remove escape sequence end heuristic from LOG
* replace Core_console with Core_log (no format specifiers)
* move test/printf to test/log
* remove `printf()` tests from the log test
* check for exact match of the log test output
base-fiasco:
* remove unused Fiasco::print_l4_threadid function
base-nova:
* remove unused hexdump utility from core
base-hw:
* remove unused Kernel::Thread::_print_* debug utilities
* always print resource summary of core during startup
* remove Kernel::Ipc_node::pd_label (not used anymore)
base*:
* Turn `printf`,`PWRN`, etc. calls into their log equivalents
Ref #1987Fix#2119
The 11n mode can forcefully be disabled by setting the 'disable_11n'
attribute to 'true'. This is workaround for certain 6200 ABG cards
that apparently do not support this mode.
Fixes#2124.
Implementing this macro provides easy access to module parameters from
outside the contrib code, i.e. the driver frontend. For now it will be
solely used by the wifi_drv.
Issue #2124.
The default iPXE settings of 8 (RXD) and 16 (TXD) lead to issues when
AMT is enabled. In most other OS drivers those descriptors are set
to 256, let us do the same. This should fix all observed issues wrt.
AMT.
Fixes#2108.
* Supply Env to Input::Session_component
* Attach input event dataspace at Input::Client
* Process input events by lambda rather than pointer
* Supply Env and a label to Input::Connection
* Wm serves valid input_session to decorator
* Per-source signal handling at input_merger
* Base API update for dummy_input_drv, test_input
* Input API update for launcher, menu_view, terminal,
mupdf, sdl, seoul, virtualbox
Ref #1987
This patch makes the build-system integration of noux packages usable
for non-Noux targets. It moves the GNU build system wrapper to
ports/mk/gnu_build.mk, which is now included by noux.mk. This way,
non-noux applications can use the same build-system wrapper. So the
porting of individual applications becomes easier.
This change removes the 'NOUX_' prefix use the various build variables
used by the noux-pkg's target.mk files to steer the behaviour of the GNU
build system. E.g., NOUX_CONFIGURE_ARGS is now called CONFIGURE_ARGS.
Note that there is a single exception to this pattern: The formerly
named NOUX_LIBS is now called LDLIBS because the plain LIBS variable is
used by the Genode build system.
Fixes#2094
* Remove 'test' routine from kernel/core
* Move 'cpu_scheduler' and 'double_list' test to user-land
* Remove 'hw_info' target at all (can be recycled in a topic branch)
Kernel fails to lookup a capability it just got delegated, if
the backing store for the destination capability was before backed by a
zero-page. Triggers if PCID (64bit) is in use or in SMP setups.
Fixes#2101
When run with the '--autopilot' run option, the 'usb_hid.run' script tests
the input events generated by a 'Pro Micro' microcontroller board. Setup
instructions for the Pro Micro can be found in the run script.
Fixes#2087
The nic_router component can be used to individually route IPv4 packets
between multiple NIC sessions. Thereby, it can translate between
different IP subnets. The component supports port forwarding, as well as
the partitioning of the TCP and UDP port spaces.
Fixes#114
A run script to demonstrate the combination of the cpu_sampler, fs_log,
ram_fs and noux components for saving the sampled data in files and
accessing these in a Noux environment. When the script is run by the
autopilot, it will check if one of the generated sample data files
contains the correct instruction pointer. When the script is run
interactively, the generated files can be accessed from a Noux Bash shell.
Fixes#2078
In other contexts (IPv4) 'calc_checksum' merely returns a new checksum that is
then installed via 'checksum'. Thus, the UDP 'calc_checksum' that calculates AND
installs a new checksum is misleading.
Ref #114
Both, client and server now read their IP config from their Genode config.
Furthermore, the client now waits 4 instead of 2 seconds before sending the
first request to prevent connection fails in tests with a slow startup. The
client truncates its packet dump for better readability.
Ref #114
This patch adds the missing exception handling for depleted RM session
quotas. If core runs out of session quota while creating a new region
map, it now reflects this condition as a Region_map::Out_of_metadata
exception to the RM client. Thanks to Denis Huber for reporting the
issue!
The '--autopilot' option makes it possible for a run script to detect if
it is being executed by the autopilot by
if { [get_cmd_switch --autopilot] } { ... }
In that case, the run script could do an automated test, whereas the
test could be interactive when run without this option.
Fixes#2076
The new parameter specifies the additional timeout duration in seconds
which is incurred by AMT log processing, e.g. time spent waiting for the
system to boot.
Although the driver makes no use of interrupts it references Irq_handler
for unknown reasons. Moreover, this commit eliminates the lock that is
not necessary anymore, because the driver now runs single-threaded.
Ref #2072
* Unify uart drivers of different hardware drivers
* Remove deprecated IRQ activations
* Remove additional timer thread in Fiasco* KDB driver
* Move more generic UART definitions to specific supported
platforms (e.g.: pl011 -> pbxa9)
* Move internal definitions from global to local headers
Ref #1987Fix#2071
Use a seperate handle at each session.
Use SEEK_TAIL to append messages to files.
Increase packet buffer.
Refactor to component framework.
Fixes#1777
Issue #2060
This patch revives our ds_ownership test from 2012, which just revealed
a regression in core where the dataspace-free operation of the RAM
service would unconditionally destroy dataspace objects from foreign
sessions. The patch fixes the bug and adds an updated version of the
test to the autopilot.
Fixes#2065
The main feature for this version upgrade is the use of the instruction
emulator (IEM) to speed up execution and less often the slow recompiler.
issue #2059
Besides adapting the components to the use of base/log.h, the patch
cleans up a few base headers, i.e., it removes unused includes from
root/component.h, specifically base/heap.h and
ram_session/ram_session.h. Hence, components that relied on the implicit
inclusion of those headers have to manually include those headers now.
While adjusting the log messages, I repeatedly stumbled over the problem
that printing char * arguments is ambiguous. It is unclear whether to
print the argument as pointer or null-terminated string. To overcome
this problem, the patch introduces a new type 'Cstring' that allows the
caller to express that the argument should be handled as null-terminated
string. As a nice side effect, with this type in place, the optional len
argument of the 'String' class could be removed. Instead of supplying a
pair of (char const *, size_t), the constructor accepts a 'Cstring'.
This, in turn, clears the way let the 'String' constructor use the new
output mechanism to assemble a string from multiple arguments (and
thereby getting rid of snprintf within Genode in the near future).
To enforce the explicit resolution of the char * ambiguity, the 'char *'
overload of the 'print' function is marked as deleted.
Issue #1987
Core on seL4 is configured to run on native hardware, so some static
allocators are bit over dimensioned. Some run scripts fail on qemu because
solely 64M are available in the system - adjust the affected scripts.
Issue #2044
The initial support reports TouchPointPressed, TouchPointMoved, and
TouchPointReleased for multiple touch points, but is currently only
tested with widgets not leveraging multi-touch events. In other words, I
made sure synthetic mouse events are generated properly when using touch
screens.
We now always run the input_merger as Input service provider and
configure backends suitable for the used platform. On x86 hardware, we
enable both, PS/2 and USB HID.
Required to boot on hardware. The fragmentation is such unfortunate with the
old allocator that alloc() will throw an exception during very early core boot
phase.
Issue #2044
- disable iommu
- increase root_cnode further for native boot
- support vesa driver on native hardware
- don't mask edge triggered ioapic irqs
- increase various allocators to get noux_tool_chain_* booting natively
Issue #2044
That seems nowadays the right place in order to tell the caller that the
thread couldn't be completely constructed. The return value false of
bind_thread causes in Cpu_thread_component the throwing of
Thread_creation_failed.
thread.run now passes
pthread.run now passes
Issue #2044
Additionally, exclude boot-module from page_table_registry. Core does not use
the boot-modules inside core.
Adding it otherwise to the registry will use up the meta data allocator of
the page_table_registry in core in scenarios with lot of boot modules,
e.g. noux and friends.
Issue #2044
- adjust syscall bindings to support -fPIC
- read serial i/o ports from BIOS data area
- use autoconf.h provided by sel4
-- to avoid ambiguity between sel4 kernel and user libraries
-- remove manual set defines
- remove debug messages
- increase user virtual area to 3GB
Issue #1720
Issue #2044
and show some message about. On sel4 sometimes exceptions are thrown and no
message is shown, it just seems to hang. With this patch at least you get
an idea that something bad happened.
Issue #2044
- remove special handling from base-nova
- add to rpc_server where it actually should be applied to
- required to work for sel4 cancel_blocking
Issue #2044
Now, we support multi-touch devices generating multi-touch events and
absolute-pointer devices simultaneously with multitouch="yes". Still,
multitouch="no" generates emulated absolute-pointer events for
multi-touch devices.
Add option to load the initial overlay*.vdi from disk, but keep the changes
in a ram_fs.
Used with AHCI model for vbox_auto_win7. Currently we have no way to tell
rump_fs to unmount and write back data to disk before resetting the machine.
On MVM only the initial scanning of APs works. If wpa_supplicant changes
from triggered scans to the scheduled-scanning hardware feature no
further scan results are reported. Therefore, we disable the
scheduled-scanning hardware feature until the issue is fixed.
Issue #2046
When running the same kernel in a VM as on the host system and the
kernel boot message from the VM appears on the log output, the run tool
assumes that the host machine has rebooted unexpectedly. With this
commit, an unexpected reboot is assumed only if the kernel boot message
appears at the beginning of a line. On base-hw, we enforce a line feed
at the beginning of the boot message as the SPIKE emulator log starts
with the first message of the kernel lacking a line feed.
Fixes#2041
Thread stacks with less than 4K usable space are insufficient for our
implementation of Linux exception signal handling. If such a unusually
small stack overflows the SIGSEGV handler will not be able to print the
diagnostic message leaving no hint of the cause of the stuck process.
The linker scripts are known to reside in BASE_DIR. By using them
directly from this location instead of searching them in the
REPOSITORIES, we don't need to specify the repos/base as a repository in
order to link.
This patch handles x86_32 and x86_64 separately since this is the SPEC
value directly supplied to the package build tool. This way, we achieve
that a CROSS_DEV_PREFIX is defined for each supported argument.
This patch equips the build system with the feature of building an
individual library with its dependencies by specifying the library
as 'LIB' argument. E.g., 'make LIB=libc' builds the libc.
This patch adds the methods 'sigh_ack_avail()' and
'sigh_ready_to_submit()', which are needed to build asynchronously
operating file-system clients.
Fixes#2023
Those headers implement a platform-specific mechanism. They are never
used by components directly.
This patch also cleans up a few other remaining platform-specific
artifact such as the Fiasco.OC-specific assert.h.
Issue #1993
Conveying the ROM filename as the final label element simplifies
routing policy and session construction.
Annotations by nfeske:
This commit also changes the ROM session to use base/log.h instead of
base/printf.h, which produced build error of VirtualBox because the
vbox headers have a '#define Log', which collides with the content of
base/log.h. Hence, this commit has to take precautions to resolve this
conflict.
The commit alse refines the previous session-label change by adding a
new 'Session_label::prefix' method and removing the use of 'char const *'
from this part of the API.
Fixes#1787
Session_label constructor now takes a bare string rather than a
serialized argument buffer.
Replace all instances of previous constructor with 'label_from_args'
function.
Issue #1787
This patch establishes the sole use of generic headers across all
kernels. The common 'native_capability.h' is based on the version of
base-sel4. All traditional L4 kernels and Linux use the same
implementation of the capability-lifetime management. On base-hw, NOVA,
Fiasco.OC, and seL4, custom implementations (based on their original
mechanisms) are used, with the potential to unify them further in the
future.
This change achieves binary compatibility of dynamically linked programs
across all kernels.
Furthermore, the patch introduces a Native_capability::print method,
which allows the easy output of the kernel-specific capability
representation using the base/log.h API.
Issue #1993
This patch alleviates the need for a Native_capability::Dst at the API
level. The former use case of this type as argument to
Deprecated_env::reinit uses the opaque Native_capability::Raw type
instead. The 'Raw' type contains the portion of the capability that is
transferred as-is when delegating the capability (i.e., when installing
the parent capability into a new component, or when installing a new
parent capability into a new forked Noux process). This information can
be retrieved via the new Native_capability::raw method.
Furthermore, this patch moves the functions for retriving the parent
capability to base/internal/parent_cap.h, which is meant to be
implemented in platform-specific ways. It replaces the former set of
startup/internal/_main_parent_cap.h headers.
Issue #1993
The static 'Thread::mystack()' function returns the stack boundaries of
the calling thread. It is useful when a thread uses a diffent stack than
the primary one.
Fixes#2037
When calling 'connect()' in nonblocking mode and the connection has been
established, don't call 'tcp_connect()' again, which would trigger an
assertion with the message 'tcp_connect: can only connect from state
CLOSED'.
Fixes#2039
In addition to modernizing the component now also supports using
empty RAM dataspace as backing store.
For example to use an ISO file the component has to be configured
as follows:
! <config file="image.iso" block_size="2048"/>
To use a empty RAM dataspace that is 256MiB large and has a block
size of 4KiB the configuration looks like this:
! <config size="256M" block_size="4096"/>
Either 'size' or 'file' has to specified. If both are declared the
'file' attribute is soley evaluated.
Issue #1987.
Fixes#2031.
Use quota large enough so that the USB driver does not attempt to
request further memory. On the Raspberry Pi, init has no slack memory
to respond to such a request.
Pass both paths, absolute path to the mount point and the relative path
from the mount point to the file, along with an open handle rather than
just an absolute path. Otherwise, fstat fails if the addressed file is
implemented by another VFS plugin.
Fixes#1789
Move Genode/vbox memory configuration check to separate
genode_check_memory_config() function and call it in platform-specific
setup machine hook of accloff/nova.
The rationale for this change is to omit the check on Muen since the
guest memory is separate and not allocated from base-hw memory.
Issue #2016
Write tick count of next kernel timer to the guest timed events page if
present. This causes the guest VM to be preempted at the requested tick
count and ensures that the guest VM can not monopolize the CPU if no
traps occur.
The base-hw kernel expects a configured switch-event from the guest VM
to base-hw with ID 30 and target vector 32 to be present in the system
policy.
Issue #2016
Switch kernel timer driver to timed event interface. The base-hw kernel
expects a configured self-event with ID 31 and target vector 32 to be
present in the system policy.
ssue #2016
Add call to genode_setup_machine prior to machine registration in
frontend machine setup code. This enables platform-specific adjustments
to the machine instance.
The new function is used on hw_x86_64_muen to clamp the processor count
to 1 as multiple virtual CPUs are not supported on this platform.
Issue #2016
* Implement VMMR0_DO_VMMR0_INIT operation for Muen
- Indicate VT-x support
- Enable unrestricted guest mode
- Set CR[0|4] mask to enable masking of guest CR0.[NE,NW,CD] and
CR4.VMXE bits.
* Implement VMMR0_DO_GVMM_CREATE_VM on Muen
Return error if trying to create SMP VM as VMs with multiple CPUs are
currently not supported on hw_x86_64_muen.
* Add Muen-specific Mem_region type
On hw_x86_64_muen the guest memory layout is static, thus regions are
handed out from an array of memory regions.
Use sinfo API to calculate the base address of the VM RAM physical
0x0 region. This allows to dynamically modify the VM RAM size by
adjusting the Muen policy and Genode vbox files accordingly.
Zeroize all memory regions apart from VM Ram since Virtualbox expects
these regions to be cleared.
* Add Muen subject state struct
The subject state encompasses the guest VM machine state that is
transfered between Virtualbox and hardware accelerated execution on
Muen.
* Add Muen-specific Vm_handler class
* Use Vm_handler to run VM
* Instruct recompiler to flush its code cache
* Copy the Muen subject state to/from the Vbox PCPUMCTX.
* Use the VM interruptibility state to inform the recompiler whether
interrupts are currently inhibited.
* Explicitly handle control register access
If a VM-exit occurs due to a control register access, handle it and
directly continue hardware accelerated execution of guest VM.
Note: On NOVA control register accesses are handled by the kernel [1].
[1] - https://github.com/alex-ab/NOVA/blob/master/src/ec_vmx.cpp#L106
* Reset guest interruptibility state
Assert that interrupts are not inhibited in the Virtualbox machine
state and clear Blocking-by-[STI|MOV to SS] guest interruptibility
flags prior to running a guest VM in hwaccel mode.
* Set return code depending on exit reason
Do not unconditionally emulate the next instruction on VM exit. This
makes sharing the VM FPU state with Virtualbox unnecessary, as FPU
instructions are not emulated by the recompiler any longer.
Also, assert that the FPU has not been used by the recompiler
* Inject pending guest VM interrupts on Muen
Use mapped subject pending interrupts page of guest VM to perform
interrupt injection. IRQs are transferred from the Virtualbox trap
manager state to the pending interrupts region for injection. If an
IRQ remains pending upon returning to the recompiler, it is copied
back to the trap manager state and cleared in the subject interrupts
region.
* Inform recompiler about changed SYSENTER_[CS|EIP|ESP] values,
otherwise values set while running the guest VM hardware accelerated
may get lost.
* Implement genode_cpu_hz() on Muen
Determine the CPU frequency dynamically using the sinfo API.
Issue #2016
* The Vm thread is always paused and on exception to make sure that guest VM
execution is suspended whenever we handle an interrupt. Also signal the Vm
session to poke waiting threads (e.g. Virtualbox EMT).
* Implement Vm::proceed
Switch to the mode transition assembly code declared at the _vt_vm_entry
label.
Issue #2016
The entry enables interrupts and initiates a handover to the guest VM by
invoking event number one. The sti instruction is placed at the start to
allow exits to Muen before handing off to the VM if window exiting is
requested.
Issue #2016
The virtual PCI model delivers IRQs to the PIC by default and to the
IOAPIC only if the guest operating system selected the IOAPIC with the
'_PIC' ACPI method and if it called the '_PRT' ACPI method afterwards.
When running a guest operating system which uses the IOAPIC, but does
not call these ACPI methods (for example Genode/NOVA), the new
configuration option
<config force_ioapic="yes">
enforces the delivery of PCI IRQs to the IOAPIC.
Fixes#2029
The alternate stack must use the stack area as, e.g., Thread::myself()
depends on this property. Hybrid components do not depend on this
property and, therefore, use a static stack buffer.
Fixes#1935
* Align pitch value to 64 byte (thanks to cnuke for investigation)
* Get rid of extra dataspace retrival and attachment, now that we always buffer
* Consistently name all lx_emul helpers: lx_* (get rid of dde*)
* Add missing file headers
Fix#1997
Instead of providing a buffer to the client and blitting from that
to the "real" framebuffer as an option, with this commit we always do so.
Thereby its possible to immediately destroy the old framebuffer used by
hardware when a configuration change is done, and a new framebuffer
is used. This also simplifies the modesetting.
Moreover, this commit fixes an issue when not using the connector reporting.
Until now the initial mode detection of connectors was only done when
the report was created. this is a regression that entered the driver
when upgrading to the recent Linux kernel version.
Ref #1997
Use new env, component and logging frameworks.
Sync file system and block device on component entrypoint.
Support for 'root' session argument.
Increase Rump open file descriptor limit.
Issue #1987Fixes#2011
* remove all 'Genode::env()' calls
* use attached roms to read configuration
* use compoenent framework
* remove all PDBG, PINF, PWRN macros
Issue #1987Fixes#2019
* use Component::* instead of Server::*
* do not use old printf format anymore
* do not use old Genode::env()->heap() anymore
* avoid pointers where possible, and use references instead
* throw away the thread-safe variants of list and AVL tree,
nic_bridge became single-threaded in the past
* introduce Ram_session_guard instead of Allocator_guard
Issue #1987
- platform_drv announces a separate "Acpi" session
- platform_drv waits for ROM "system" to change state to "acpi_ready"
- acpica waits for "Acpi" announcement
- acpica uses the platform driver via "Acpi" to reconfigure PCI devices
- acpica changes "system" state to "acpi_ready" after it ready with initialization
- platform_drv reacts on "system" state change to "acpi_ready" by announcing "Platform" session
- drivers start to operate as usual
Issue #2009
This patch introduces the Genode::raw function that prints output
directly via a low-level kernel mechanism, if available.
On base-linux, it replaces the former 'raw_write_str' function.
On base-hw, it replaces the former kernel/log.h interface.
Fixes#2012
This is a follow-up commit to "slab: throw exception if initial
allocation fails". It is needed because on seL4, the PD session quota is
used as backing store for the meta data of the PD's virtual memory. For
this reason, PD sessions on seL4 require more session quota compared to
the other kernels. Apparently, the default quota is too scarce to
complete the PD-session construction. By shrinking the number of
supported page-table entries, we reduce the size of the PD session
component so that the creation succeeds.
Issue #1983
Replace 'attribute(...).has_value("yes")`
with 'attribute_value(..., false)'.
This allows for boolean configuration to be set with values such as
"true", "false", "yes", "no", or "1", "0".
Fixes#2002
A configuration policy must match against a policy node label,
label_prefix, or label_suffix atttribute. A fallback to
<default-policy/> is provided as a label wildcard.
Fixes#1901
The sinfo function declared in sinfo_instance.h creates a static sinfo
object instance and returns a pointer to the caller.
- kernel timer and platform support to use sinfo() function to
instantiate sinfo object
- address and size of the base-hw RAM region via the sinfo API
- log_status() function in sinfo API
To circumvent problems on platforms with shaky hotplug interrupt notification
introduce a "poll" configuration option to the driver, which enables
polling for connector changes.
Fix#2004
The whole XML comment has to be parsed as one XML tag to support strange
but valid combinations like
<!---->
<!--invisible-tag></invisible-tag-->
Fixes#1424
The vanilla 'schedule_timeout()' Linux function expects a relative
timeout value. The first implementation of the wifi_drv, however, used
an absolute timeout value. This mismatch was overlooked when the
lx_kit, which adheres to the vanilla Linux semantics, was incoporated
in the driver.
Fixes#1990.
Instead of introducing a $(BASE_HW_DIR) variable that has to be defined in each
core makefile for the different base-hw targets, this commit replaces the
$(REP_DIR) variable usage in core.inc files with $(BASE_DIR)/../base-hw.
Ref #1955
Quota_exceeded message are of no use during session construction, since
the arguments of the ram_quota are used and no upgrade can take place (the
session construction failed and is so not available for upgrade)
Fixes#1983
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
